Genuine Jeep Comanche Ignition Coil

Ignition Coil Resistor

Enter your vehicle info to find more parts and verify fitment

  • Select Vehicle by VIN
  • Select Vehicle by Model
Select by VIN
Enter your VIN for the most accurate results.
Enter your VIN for the most accurate results.
or
Select by Model
-- Select Make --
-- Select Model --
-- Select Year --

3 Ignition Coils found

  • Jeep Comanche Ignition Coil - 33004522
    Diagram for Jeep Comanche Ignition Coil - 33004522
    View related parts

    Jeep Comanche Ignition Coil

    Part Number: 33004522
    • Other Name: Coil, Ignition Carbureted Engine
    $71.04 MSRP: $90.40
    You Save: $19.36 (22%)
    Add to Cart
    More Info
    Fits the following Vehicles:
    • 1987-1992 Jeep Comanche | 3-Person Cab 2WD, 3-Person Cab 4WD | 4 Cyl 2.5L
    Less Info
  • Jeep Comanche Ignition Coil - T1031135
    Diagram for Jeep Comanche Ignition Coil - T1031135
    View related parts

    Jeep Comanche Ignition Coil Ignition

    Part Number: T1031135
    • Other Name: Coil-Ignition Engine Ignition; Ignition Coil
    More Info
    Fits the following Vehicles:
    • 1986-1990 Jeep Comanche | 4 Cyl 2.5L, 6 Cyl 4.0L
    Less Info
  • Jeep Comanche Ignition Coil - 4762312
    Diagram for Jeep Comanche Ignition Coil - 4762312
    View related parts

    Jeep Comanche Ignition Coil

    Part Number: 4762312
    • Other Name: Coil,Ignition
    More Info
    Fits the following Vehicles:
    • 1991-1992 Jeep Comanche | 3-Person Cab 2WD, 3-Person Cab 4WD | 6 Cyl 4.0L
    Less Info

Jeep Comanche Ignition Coil Parts Questions & Answers

  • Q: How to remove and install the pickup coil assembly in a distributor?
    A: Disconnect the cable from the negative battery terminal. You may remove the Distributor for ease, but it's optional. If removed, place it in a vise. Take off the distributor cap and rotor. Use a puller tool to remove the trigger wheel, using a washer to protect the inner shaft. Remove the pin, pickup coil assembly retainer, and washers. Remove the two pickup coil plate screws and lift the pickup coil assembly. Reinstall the assembly, ensuring the pin fits into the vacuum advance mechanism link hole. Secure it with washers and retainer. Position the wiring harness in the distributor housing slot. Reinstall the plate screws and trigger wheel. Use a pin punch and hammer to tap the pin into the trigger wheel and shaft groove. Reinstall the rotor and distributor cap. Reconnect the battery terminal.
  • Q: How to check and replace the ignition coil on Jeep Comanche?
    A: To replace the ignition coil on most models, disconnect the negative Battery Cable and locate the ignition coil. If necessary, unscrew the mounting bracket bolts to remove the coil. Disconnect the wires from the coil's terminals. Use an ohmmeter to test the resistance at the primary terminal and ground, the positive and negative primary terminals, and the negative primary and high voltage terminals. If any tests fail, replace the coil. To do so, disconnect the wires from the coil's terminals, remove the mounting bracket bolts and the coil. Install the new coil in reverse order. For 2000 and later inline six-cylinder models, remove and clean the ignition coil rail assembly. Check for damage and test the coil primary resistance at terminals 2 and 1, 2 and 3, and 2 and If the resistance is out of range or if there's damage, replace the entire assembly. To replace, remove the assembly, disconnect the electrical connector, and install the new assembly, ensuring all spark plug boots are properly seated. Secure with mounting bolts and reconnect the electrical connector.
  • Q: How to replace the pick-up coil in a distributor?
    A: Disconnect the battery's negative cable. Remove the Distributor cap, rotor, and pick-up coil leads. Use an ohmmeter to test the pick-up coil's resistance; it should show infinite resistance. If not, replace the coil. Test the coil's terminals; the ohmmeter should read between 500 and 1500 ohms. If not, replace the coil. Remove the distributor and rotor. Disconnect the coil leads. Remove the Hall-effect switch if present. Mark the distributor gear and shaft for reassembly. Remove the roll pin, gear, and washers from the shaft. Remove the shaft and pick-up coil. Reinstall in reverse order, using a new roll pin.

Related Jeep Comanche Parts