How to adjust the Exhaust Valve and Intake Valve clearance in the four cylinder engine on Chrysler Sebring?

Align the first piston at the top of its travel when pressing the air into the engine. Lift off the engine cover by pulling, before taking out the ball stud. Unconnect the battery cable from where it connects to its ground terminal. Clean around the spark plug openings with compressed air, if available. Then pull out the spark plugs to keep any dirt and debris from falling into the engine. Remove the valve cover. Take measurements for the valve set by finding two lobes facing straight up on one cylinder while spinning the camshaft. We will take these measurements now to help us pick the right replacement lifters later. Keep checking camshaft lobes as you spin the camshaft. Take out the camshaft(s) for the valves you plan to tweak. Take a micrometer to measure each lifter's height and replace each one in its cylinder head until all lifters have been measured. Keep track of each lifter's measurement. To find the right replacement lifter that gets the valve gap where it should be, work out the difference by using the equation S - C = change. In this equation, S is the needed valve clearance number, and C is the measurement of the current gap. Pull out the lifter and note the size value from underneath it. Then reduce the lifter length by finding the needed valve clearance difference from your measurement reading or getting it as close as possible to your calculation results. Install the camshaft(s). Make sure you recheck the valve clearances and see if they stay in the accepted range. Later stages of installation work in the opposite direction as removal did.

Genuine Chrysler Sebring Exhaust Valve

Exhaust Muffler Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Exhaust Valves found

View related parts
Chrysler Sebring Valve, Exhaust - Standard
Part Number: 4667972
$33.39 MSRP: $43.14
You Save: $9.75 (23%)
ADD TO CART
Product Specifications
- Other Name: Exhaust Valve, Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chrysler Sebring | JX, JXi, LX | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 4892094AB
$25.41 MSRP: $51.85
You Save: $26.44 (51%)
ADD TO CART
Product Specifications
- Other Name: Valve Exhaust Standard; Exhaust Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, Touring Sedan | 6 Cyl 3.5L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 4884690AA
$32.54 MSRP: $45.35
You Save: $12.81 (29%)
ADD TO CART
Product Specifications
- Other Name: Valve Exhaust Standard; Exhaust Valve, Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chrysler Sebring | Base Convertible, Base Sedan, Limited Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: MD306183
$10.73 MSRP: $16.90
You Save: $6.17 (37%)
ADD TO CART
Product Specifications
- Other Name: Valve Exhaust Standard; Exhaust Valve, Valve
- Replaces: MD303177
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2005 Chrysler Sebring | Base, JX, JXi, LX, LXi | 4 Cyl 2.4L, 6 Cyl 2.5L, 6 Cyl 3.0L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 4648613
$15.23 MSRP: $19.69
You Save: $4.46 (23%)
ADD TO CART
Product Specifications
- Other Name: Valve Exhaust Standard; Exhaust Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-1998 Chrysler Sebring | JX | 4 Cyl 2.0L
View related parts
Chrysler Sebring Engine Exhaust Valve
Part Number: MN183950
$35.94 MSRP: $51.75
You Save: $15.81 (31%)
ADD TO CART
Product Specifications
- Other Name: Valve Engine Exhaust
- Replaced by: 5047069AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chrysler Sebring | Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Engine Exhaust Valve
Part Number: 5047069AA
$35.94 MSRP: $51.75
You Save: $15.81 (31%)
ADD TO CART
Product Specifications
- Other Name: Valve Engine Exhaust
- Replaced by: 5047069AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chrysler Sebring | Limited Sedan, LX Convertible, LX Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 4663902
$29.42 MSRP: $43.15
You Save: $13.73 (32%)
ADD TO CART
Product Specifications
- Other Name: Valve Exhaust Standard; Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2010 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan, Touring Convertible, Touring Sedan, TSI Sedan | 6 Cyl 2.7L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: MD303177
$10.60 MSRP: $16.90
You Save: $6.30 (38%)
ADD TO CART
Product Specifications
- Other Name: Valve Exhaust Standard
- Replaced by: MD306183
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | Base, LX | 4 Cyl 2.4L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 4852361AA
Product Specifications
- Other Name: Valve Exhaust Standard
- Replaced by: 4852361AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Sedan, Touring Sedan
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 4777899AA
Product Specifications
- Other Name: Valve Exhaust .015" O/S
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Valve Exhaust Standard
Part Number: 4777898AA
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2004 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 4852361AB
Product Specifications
- Other Name: Valve Exhaust Standard; Exhaust Valve
- Replaces: 4852361AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Sedan, Touring Sedan
View related parts
Chrysler Sebring Exhaust Valve
Part Number: 68001583AA
Product Specifications
- Other Name: Valve Exhaust Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, Touring Sedan

Chrysler Sebring Exhaust Valve

Exhaust Valve is a significant component of Chrysler Sebring Automobiles which helps in the combustion engine to expel the burnt exhaust gases from the cylinders of the car's engine. This function is very important to maintain the optimal engine operations for if the Exhaust Valve is affected there may be some problems such as less power, misfires, rough idle, and low fuel economy. It is possible that Chrysler Sebring models of different years use different kinds of Exhaust Valves, however, the latter is not described in details. The main process of functioning of the Exhaust Valve is provided by its opening and closing cycle, which plays a crucial role in the further performance of the engine. Charging of good working of Chrysler Sebring vehicles rests on the integrity of the Exhaust Valve.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Sebring Exhaust Valve at great affordable prices. Moreover, all genuine Chrysler Sebring Exhaust Valve come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Sebring Exhaust Valve Parts Questions & Experts Answers

Exhaust Valve
4892094AB
Q: How to adjust the Exhaust Valve and Intake Valve clearance in the four cylinder engine on Chrysler Sebring?
A:
Align the first piston at the top of its travel when pressing the air into the engine. Lift off the engine cover by pulling, before taking out the ball stud. Unconnect the battery cable from where it connects to its ground terminal. Clean around the spark plug openings with compressed air, if available. Then pull out the spark plugs to keep any dirt and debris from falling into the engine. Remove the valve cover. Take measurements for the valve set by finding two lobes facing straight up on one cylinder while spinning the camshaft. We will take these measurements now to help us pick the right replacement lifters later. Keep checking camshaft lobes as you spin the camshaft. Take out the camshaft(s) for the valves you plan to tweak. Take a micrometer to measure each lifter's height and replace each one in its cylinder head until all lifters have been measured. Keep track of each lifter's measurement. To find the right replacement lifter that gets the valve gap where it should be, work out the difference by using the equation S - C = change. In this equation, S is the needed valve clearance number, and C is the measurement of the current gap. Pull out the lifter and note the size value from underneath it. Then reduce the lifter length by finding the needed valve clearance difference from your measurement reading or getting it as close as possible to your calculation results. Install the camshaft(s). Make sure you recheck the valve clearances and see if they stay in the accepted range. Later stages of installation work in the opposite direction as removal did.