My Garage
My Account
Cart
Genuine Chrysler Sebring Heater Core
HVAC Heater Core- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
7 Heater Cores found
Chrysler Sebring Heater Core
Heater Core in Chrysler Sebring automobile is also responsible for blowing hot air into the car cabin each time the heater is turned on. Of the same work as a radiator in general the Heater Core use the water-and-antifreeze mixture to take heat away from the engine. This heat is then transferred to the air that is to be supplied to the cabin by a fan that circulates air over the core This core is usually made up of materials such as aluminum or brass and isprovided with fins to improve heat transfer. Through the years of manufacture of Chrysler Sebring models there could be variations of the Heater Core design, the kind of valves with flow regulating properties or doors to block the core. Higher tier systems may use electromechanical actuators to finely control the environments temperature. Problems associated with the Heater Core consist of blockage, leaking, and corrosion and this commonly present some kind of difficulty in the process of repairing because the dashboard may have to be almost dismantled.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Sebring Heater Core at great affordable prices. Moreover, all genuine Chrysler Sebring Heater Core come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Chrysler Sebring Heater Core Parts Questions & Experts Answers
- Q: How to replace Heater Core on Chrysler Sebring?A:Special custom-built tools are needed to take off trim inside cars made before 2014 without causing any harm to these clips. You will need to have these special removal tools with you while taking apart your vehicle's interior parts. Start by asking a professional to drain out the refrigerant and collect it from your air conditioning system. Separate the car's power from the remote battery anchor point. Drain the cooling system. Twist and lower the heat shield by removing a nut on top of the firewall on the driver's side. Then take off another two nuts that keep the shield attached to bolts on the dashboard. Untighten the bolt that holds the refrigerant lines to the evaporator of the air conditioner. Take off the lines, and extract the seals. Block line openings with plugs or tape to keep out moisture and dirt. Put towels under the tube fits. Remove clamps and disconnect heater hoses from the heater core. Plug or tape over openings to avoid spillage. Lift the heating/air conditioning housing from the instrument panel using the bolts, then peel off the front trim on both passenger and driver sides. Then, take out the front seats. When present, take out and offline the secondary amplifier is the passenger side. Pull out the side trim panels by the B pillar, next to the windshield. Also take off the trim panel directly above the driver's seat. First uncover the floor where the seats meet, then take out the dashboard. Take the shift interlock cable away from the floor duct and move it out of your way. Take out the screws that hold the air duct to the heating/air conditioner housing on the driver's side, and afterwards remove the duct and the tube that drains water from the air conditioner. Use pliers to get rid of the bolts that fasten the left and right back ducts to their housing over the heating and air conditioning system. Take out the dash panel passenger's side heater/air conditioning housing nut, then gently tug the heating system forward and pull it out through the passenger compartment, making sure towels cover the insides to catch any flowing fluids. On a workbench, pry the foam seal from the metal flange that holds the heater core tubes. Then unpin the metal flange from the heater/air conditioning housing and detach it. Untighten and take off the fasteners connected to both the heat core retaining brackets and the heater core line retaining brackets. After that, cautiously pull the heater core out from its place inside the housing. To install a new heater core, you replace the old seals where the fittings connect and fill the cooling system again. You'll need first to drain and flush the cooling system when putting in a fresh heater core.
