How to remove and install Pushrod and rocker arm in 3.3L and 3.8L V6 engine on Chrysler Town & Country?

To remove the valve covers, first loosen each rocker arm shaft bolt gradually until they can be removed by hand, starting with the outer ones. Next, take out the rocker arm and shaft assembly, noting the positioning of the rocker arms, washers, and shaft retainer/spacers if they are removed. Use pliers to grip the edges of the retainer/spacers and pull them straight up off the shaft. Remove the pushrods and store them in order to avoid mixing them up during installation. Inspect each rocker arm for wear, cracks, and damage, particularly at the ball socket pivots and tips, and check the pivot seat and faces for galling and unusual wear patterns; replace any worn or damaged rocker arms and install new pivots or shafts as necessary. For shaft-mounted rocker arms, inspect the shafts for galling and excessive wear, and check the oil holes for plugging. Examine the pushrods for cracks and excessive wear at the ends, rolling each across a piece of plate glass to check for bending. When installing, ensure the longer rocker shaft bolt is placed correctly, and tighten the rocker shafts slowly, starting with the center bolts and moving outward, allowing at least 20 minutes for bleed-down after installation. Lubricate the lower end of each pushrod with clean engine oil or moly-base grease and install them in their original locations, ensuring they seat completely in the lifter socket. Apply moly-base grease to the ends of the valve stems and the upper ends of the pushrods, as well as to the rocker arm shaft. If removed, install the rocker arms, washers, shaft retainer/spacers, and bolts in the correct order, then attach the rocker arm assembly to the cylinder head, tightening the bolts gradually from the center outward to the specified torque while ensuring the pushrods engage properly in the rocker arms. Allow the engine to set for 20 minutes before starting, and finally, install the valve covers.

Genuine Chrysler Town & Country Rocker Arm

Engine Rocker Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Rocker Arms found

View related parts
Chrysler Town & Country Engine Rocker Arms
Part Number: 68027600AA
$43.01 MSRP: $74.55
You Save: $31.54 (43%)
ADD TO CART
Product Specifications
- Other Name: Arm-Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013 Chrysler Town & Country
- 2008-2011 Chrysler Town & Country | Limited, LX, Touring, Touring Plus
View related parts
Chrysler Town & Country Engine Intake Rocker Arm
Part Number: 4573460
$60.64 MSRP: $90.25
You Save: $29.61 (33%)
ADD TO CART
Product Specifications
- Other Name: Arm-Intake; Exhaust Rocker Arm, Intake Rocker Arm
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 4.0L
View related parts
Chrysler Town & Country Arm-Intake
Part Number: 4573459
$60.64 MSRP: $90.25
You Save: $29.61 (33%)
ADD TO CART
Product Specifications
- Other Name: Rocker Arm Intake; Exhaust Rocker Arm, Intake Rocker Arm
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 4.0L
View related parts
Chrysler Town & Country Engine Valve Arm
Part Number: 5184296AF
$20.97 MSRP: $30.00
You Save: $9.03 (31%)
ADD TO CART
Product Specifications
- Other Name: Rocker Arm Valve
- Replaced by: 5184296AH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2016 Chrysler Town & Country | Limited, Limited Platinum, LX, S, Touring, Touring L, Touring-L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Rocker Arm Kit
Part Number: 5184296AE
$20.97 MSRP: $30.00
You Save: $9.03 (31%)
ADD TO CART
Product Specifications
- Other Name: Rocker Arm Valve
- Replaced by: 5184296AH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chrysler Town & Country | Gold, Limited, LX, S, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Engine Intake Rocker Arm
Part Number: 4781183AA
$89.78 MSRP: $134.00
You Save: $44.22 (33%)
ADD TO CART
Product Specifications
- Other Name: Arm-Intake; Rocker Arms
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2010 Chrysler Town & Country | Base, EL, EX, Limited, Limited AWD, Limited FWD, LX, LX AWD, LX FWD, LXi AWD, LXi FWD, Touring, Touring AWD, Touring FWD, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Exhaust Rocker Arm
Part Number: 4781182AA
$110.08 MSRP: $165.00
You Save: $54.92 (34%)
ADD TO CART
Product Specifications
- Other Name: Arm-Exhaust; Rocker Arms
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2010 Chrysler Town & Country | Base, EL, EX, Limited, Limited AWD, Limited FWD, LX, LX AWD, LX FWD, LXi AWD, LXi FWD, Touring, Touring AWD, Touring FWD, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Rocker Arm Valve
Part Number: 4483725
$6.96 MSRP: $35.45
You Save: $28.49 (81%)
ADD TO CART
Product Specifications
- Other Name: Arm-Valve ; Rocker, Valve; Rocker Arms
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-2000 Chrysler Town & Country | Base AWD, Base FWD, Limited AWD, Limited FWD, LX AWD, LX FWD, LX Long Wheelbase AWD, LX Long Wheelbase FWD, LX Short Wheelbase FWD, LXi AWD, LXi FWD, SX | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Exhaust Rocker Arm
Part Number: 4663996
$74.62 MSRP: $113.00
You Save: $38.38 (34%)
Product Specifications
- Other Name: Rocker Arm Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 4.0L
View related parts
Chrysler Town & Country Engine Rocker Arm
Part Number: 4884042AA
Product Specifications
- Other Name: Rocker Arm Valve Roller; Rocker Arms
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Chrysler Town & Country | Base, EL, LX FWD, LXi FWD
View related parts
Chrysler Town & Country Rocker Arm Inlet & Exhaust
Part Number: MD195450
Product Specifications
- Other Name: Rocker Arm, Inlet and Exhaust Valve; Rocker Arms
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Town & Country | LX FWD, LXi FWD, SX
- 1993-1996 Chrysler Town & Country | LX Long Wheelbase FWD, LX Short Wheelbase FWD

Chrysler Town & Country Rocker Arm

Rocker Arm in Chrysler Town & Country vehicles has a great importance in the valvetrain system of the car's engine as it helps to transfer movement started from the pushrod to the specific directions of the intake/exhaust valves. Usually made from stamped steel or aluminum, The Rocker Arm has the capability of translating vertical pushrod movement into the right amount of force needed to open the valves. High-revving engines require light weight and good thermal conductivity, hence, the use of aluminum while cast iron or forged carbon steel gives improved strength in diesels. Chrysler Town & Country models may incorporate roller rockers which employ bearing to minimize the contact of components enhancing their efficiency as compared to their leaf counterparts. The rocker ratio has increased from 1.44:1- 1.71:1 in modern engines and can bring in more camshaft lift thus improving performance. The upgraded fulcrum bearings are also employed in high-RPM engines in order to cope with the load and enhance the performance and recyclability of the Rocker Arm in Chrysler Town & Country automobiles.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Town & Country Rocker Arm at great affordable prices. Moreover, all genuine Chrysler Town & Country Rocker Arm come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Town & Country Rocker Arm Parts Questions & Experts Answers

Engine Intake Rocker Arm
4781183AA
Q: How to remove and install Pushrod and rocker arm in 3.3L and 3.8L V6 engine on Chrysler Town & Country?
A:
To remove the valve covers, first loosen each rocker arm shaft bolt gradually until they can be removed by hand, starting with the outer ones. Next, take out the rocker arm and shaft assembly, noting the positioning of the rocker arms, washers, and shaft retainer/spacers if they are removed. Use pliers to grip the edges of the retainer/spacers and pull them straight up off the shaft. Remove the pushrods and store them in order to avoid mixing them up during installation. Inspect each rocker arm for wear, cracks, and damage, particularly at the ball socket pivots and tips, and check the pivot seat and faces for galling and unusual wear patterns; replace any worn or damaged rocker arms and install new pivots or shafts as necessary. For shaft-mounted rocker arms, inspect the shafts for galling and excessive wear, and check the oil holes for plugging. Examine the pushrods for cracks and excessive wear at the ends, rolling each across a piece of plate glass to check for bending. When installing, ensure the longer rocker shaft bolt is placed correctly, and tighten the rocker shafts slowly, starting with the center bolts and moving outward, allowing at least 20 minutes for bleed-down after installation. Lubricate the lower end of each pushrod with clean engine oil or moly-base grease and install them in their original locations, ensuring they seat completely in the lifter socket. Apply moly-base grease to the ends of the valve stems and the upper ends of the pushrods, as well as to the rocker arm shaft. If removed, install the rocker arms, washers, shaft retainer/spacers, and bolts in the correct order, then attach the rocker arm assembly to the cylinder head, tightening the bolts gradually from the center outward to the specified torque while ensuring the pushrods engage properly in the rocker arms. Allow the engine to set for 20 minutes before starting, and finally, install the valve covers.