How do you remove and install the shift cable on Chrysler Town & Country?

To uninstall the shift cable, a car owner should lift the hood and cover the left fender with a blanket to avoid the scratches. Subsequently, you should pull out the cruise control actuator but do not cut the cables while doing so. Then, remove the battery and the battery tray which is located in the rear of the SMT component. Shift cable-first in the engine compartment, remove the shift cable from the shift lever by using the trim panel tool or flat bladed screw driver, again, second, loosen up the cable from the bracket by merely pulling the two black tabs and then removing the cable through the slot. The process still continues inside the vehicle in which the lower trim panel and knee bolster must be detached. Behind the steering column, unbolt the shift cable from the gear shift lever stud, and right from the steering column bracket, by using a screwdriver to pry open the housing and pushing the tabs and slipping the cable through. Partially open the panel by unclipping the grommet in the opening near the rear part of the engine compartment; pull out and disconnect the cable on the passengers' side. To install, insert the shift cable through the panel opening into the engine compartment and fit the largest end with clip on the shift lever stud; make sure it is securely seated Then engage the cable bracket and shift lever. The remaining part of the installation is done in the reverse procedure of the removal, then fine-tune the shift cable by parking the vehicle on the flat ground and engaging the parking lock. Insert the shift lever into gear and turn the key in the ignition to the off position. Release the lock plug of the shift cable adjustment screw at the transaxle shift lever, with the shift lever at the transaxle being in Park and the parking pawl engaged. Retighten the adjustment screw and see that the shift lever moves smoothly; the engine should start only in 'P' or 'N' positions. Last but not the least, change the gear shift lever of the transaxle through all the gears in order to check if all the cables are in good order and in case of any problem, then adjust the same.

Genuine Chrysler Town & Country Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

26 Shift Cables found

View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 68080123AF
$156.38 MSRP: $236.00
You Save: $79.62 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control; Shift Control Cable
- Replaces: 68080123AD, 68080123AA, 68080123AE, 68080123AB, 68080123AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chrysler Town & Country | Gold, Limited, Limited Platinum, LX, S, Touring, Touring L, Touring-L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 68080123AB
$156.38 MSRP: $236.00
You Save: $79.62 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 68080123AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Chrysler Town & Country | Gold, Limited, LX, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Gear Shift Control Cable
Part Number: 4377317
$101.84 MSRP: $129.59
You Save: $27.75 (22%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gear Shift Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | 6 Cyl 3.0L, 6 Cyl 3.3L
- 1986-1988 Chrysler Town & Country | 4 Cyl 2.2L, 4 Cyl 2.5L
- 1984 Chrysler Town & Country | 4 Cyl 2.2L, 4 Cyl 2.6L
View More
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 4670122AF
$155.66 MSRP: $234.00
You Save: $78.34 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 4670122AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002 Chrysler Town & Country | EL, EX, Limited AWD, Limited FWD, LX AWD, LX FWD, LXi AWD, LXi FWD | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 5133190AA
$89.11 MSRP: $132.00
You Save: $42.89 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable Package Gearshift Control
- Replaced by: 5133190AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Chrysler Town & Country | Base, EX, Limited FWD, LX FWD, Touring FWD | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 68080123AE
$156.38 MSRP: $236.00
You Save: $79.62 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 68080123AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012 Chrysler Town & Country | Limited, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Cable-Gearshift Control Cover
Part Number: 4504344
$132.49 MSRP: $168.60
You Save: $36.11 (22%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gear Shift Control C/Over ; Cable, G/Shift Crossover, 46.92" Lg.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1993 Chrysler Town & Country
View related parts
Chrysler Town & Country Cable Gear Shift Cont
Part Number: 4377304
$11.58 MSRP: $14.74
You Save: $3.16 (22%)
ADD TO CART
Product Specifications
- Other Name: Cable, Gearshift Control, 56.10" Lg.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1986-1988 Chrysler Town & Country | 4 Cyl 2.2L, 4 Cyl 2.5L
View related parts
Chrysler Town & Country Gearshift Control Cable
Part Number: 4543047
$36.43 MSRP: $46.36
You Save: $9.93 (22%)
ADD TO CART
Product Specifications
- Other Name: Cable-Atx Shifter ; Cable, Gearshift Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991 Chrysler Town & Country | 6 Cyl 3.3L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 5133190AB
$89.11 MSRP: $132.00
You Save: $42.89 (33%)
Product Specifications
- Other Name: Cable Package Gearshift Control; Shift Control Cable
- Replaces: 5133190AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Chrysler Town & Country | Base, EX, Limited FWD, LX FWD, Touring FWD | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 4670122
Product Specifications
- Other Name: Cable-Shifter (Col)
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chrysler Town & Country | Limited AWD, Limited FWD, LX AWD, LX FWD, LX Long Wheelbase AWD, LX Long Wheelbase FWD, LX Short Wheelbase FWD, LXi AWD, LXi FWD, SX | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 4641755
Product Specifications
- Other Name: Cable-Shifter (3-Speed)
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Chrysler Town & Country
- 1996 Chrysler Town & Country
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 4504342
Product Specifications
- Other Name: Cable, Gearshift Control Selector, (52"long)
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994 Chrysler Town & Country
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 4880207AF
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 4880207AH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Town & Country | Limited, Touring | 6 Cyl 3.3L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Cable, Gearshift Control
Part Number: 4670136
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1995 Chrysler Town & Country | Base AWD, Base FWD | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 4641755AD
Product Specifications
- Other Name: Cable-Gearshift Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Chrysler Town & Country | EL, LX FWD
View related parts
Chrysler Town & Country Gear Shift Control Cable
Part Number: 4504341
Product Specifications
- Other Name: Cable-Gear Shift Control Selector ; Cable, G/Shift Selector, 51.25" Lg.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1993 Chrysler Town & Country
View related parts
Chrysler Town & Country Gear Shift Control Cable
Part Number: 4504339
Product Specifications
- Other Name: Cable-Gear Shift Control Selector ; Cable, Gearshift Control Crossover, (45.37"Long); Overhaul Gasket Set, Valve Grind Gasket Kit
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994 Chrysler Town & Country
View related parts
Chrysler Town & Country Gear Shift Control Cable
Part Number: 4377302
Product Specifications
- Other Name: Cable-Gear Shift Control ; Cable, Gearshift Control, 56.10" Lg.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1986-1988 Chrysler Town & Country | 4 Cyl 2.2L, 4 Cyl 2.5L
View related parts
Chrysler Town & Country Transmission Gearshift Control Cable
Part Number: 4880207AG
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 4880207AH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.8L, 6 Cyl 4.0L

| Page 1 of 2 |Next >

1-20 of 26 Results

Chrysler Town & Country Shift Cable

The Chrysler Town & Country Shift Cable connects the gear selector in the cabin to the transmission, helping drivers select gears with solid, prompt motion. Previously, the linkage rods on the earlier Town & Country were rigid. The system later changed, using a flexible Shift Cable to fit tight front wheel drive layouts. With this change, it would cut down on vibration at the lever. The sliding core of this Shift Cable is located inside a low friction sheath. Thus, a simple push or pull at the shifter is converted into a movement of the transmission manual lever. Therefore, this design ensures correct PRNDL changes. The Shift Cable takes up less space than rods, resists road grime, and quiets the cabin. These benefits are now available on many Chrysler models. Over the years, Town & Country minivans employed a single-cable arrangement for the automatics, while rare manual versions required twin cables, one to select the gate and the other to engage the gear. Over time, stretching can make the feel sloppy and breakage will lock the van in one gear. A new line will restore the crisp shifts. Keeping the Chrysler Town & Country Shift Cable lubricated will ensure many more miles.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Town & Country Shift Cable at great affordable prices. Moreover, all genuine Chrysler Town & Country Shift Cable come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Town & Country Shift Cable Parts Questions & Experts Answers

Transmission Gearshift Control Cable
5133190AB
Q: How do you remove and install the shift cable on Chrysler Town & Country?
A:
To uninstall the shift cable, a car owner should lift the hood and cover the left fender with a blanket to avoid the scratches. Subsequently, you should pull out the cruise control actuator but do not cut the cables while doing so. Then, remove the battery and the battery tray which is located in the rear of the SMT component. Shift cable-first in the engine compartment, remove the shift cable from the shift lever by using the trim panel tool or flat bladed screw driver, again, second, loosen up the cable from the bracket by merely pulling the two black tabs and then removing the cable through the slot. The process still continues inside the vehicle in which the lower trim panel and knee bolster must be detached. Behind the steering column, unbolt the shift cable from the gear shift lever stud, and right from the steering column bracket, by using a screwdriver to pry open the housing and pushing the tabs and slipping the cable through. Partially open the panel by unclipping the grommet in the opening near the rear part of the engine compartment; pull out and disconnect the cable on the passengers' side. To install, insert the shift cable through the panel opening into the engine compartment and fit the largest end with clip on the shift lever stud; make sure it is securely seated Then engage the cable bracket and shift lever. The remaining part of the installation is done in the reverse procedure of the removal, then fine-tune the shift cable by parking the vehicle on the flat ground and engaging the parking lock. Insert the shift lever into gear and turn the key in the ignition to the off position. Release the lock plug of the shift cable adjustment screw at the transaxle shift lever, with the shift lever at the transaxle being in Park and the parking pawl engaged. Retighten the adjustment screw and see that the shift lever moves smoothly; the engine should start only in 'P' or 'N' positions. Last but not the least, change the gear shift lever of the transaxle through all the gears in order to check if all the cables are in good order and in case of any problem, then adjust the same.