How to remove and replace a Wheel Hub and bearing assembly on Dodge Nitro?

The hub and bearing assembly cannot be disassembled and must be replaced if either component is damaged or worn. To remove the assembly, start by removing the wheel center cap/hubcap on 4WD models. Loosen the drive axle/hub nut and the front wheel lug nuts. Raise the front of the vehicle and secure it on jack stands. Remove the wheel, disc brake caliper, caliper mounting bracket, brake disc, ABS wheel speed sensor, and sensor wire bracket. On 4WD models, remove the axle hub nut. Unbolt the hub assembly from the steering knuckle and tap it out of the knuckle bore. If the drive axle sticks in the hub splines, use a puller to push it out. To install the new hub assembly, clean the opening in the steering knuckle and attach the assembly, tightening the hub-to-knuckle bolts securely. On 4WD models, install and tighten the hub nut. Complete the installation by following the reverse steps of removal. Lower the vehicle and tighten the hub nut and lug nuts to the specified torque.

Genuine Dodge Nitro Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Wheel Hubs found

View related parts
Dodge Nitro Brake Hub And Bearing
Part Number: 2AMVH947AA
$100.58 MSRP: $175.00
You Save: $74.42 (43%)
ADD TO CART
Product Specifications
- Other Name: Hub&BRG-Brake
- Replaced by: 1BP00228AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Front Hub And Bearing
Part Number: 52109947AF
$157.50 MSRP: $234.00
You Save: $76.50 (33%)
ADD TO CART
Product Specifications
- Other Name: Hub And Bearing Brake Front; Front Hub & Bearing, Hub & Bearing
- Replaces: 52109947AD, 52109947AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Wheel Hub Front
Part Number: 52109947AD
$157.50 MSRP: $234.00
You Save: $76.50 (33%)
ADD TO CART
Product Specifications
- Other Name: Hub And Bearing Brake Front
- Replaced by: 52109947AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Nitro | SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Hub And Bearing
Part Number: 52109947AE
$157.50 MSRP: $234.00
You Save: $76.50 (33%)
ADD TO CART
Product Specifications
- Other Name: Hub And Bearing Brake Front
- Replaced by: 52109947AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L

Dodge Nitro Wheel Hub

The Wheel Hub of Dodge Nitro cars is responsible for securing the wheels of the car and harbors other important part such as bearings of the wheel and the brake system. This assemblage lets wheels rotate freely and fix them tightly to the car body, enhancing the vehicle's safety and steering stability. Some Dodge Nitro models can come with a variety of Wheel Hub that can come with different requirements including the bolt one and the axle extension width. However, when it is time to replace a Wheel Hub one has to go for a product that is a direct replacement part to fit the needs of the vehicle. The cost of a Dodge Nitro Wheel Hub replacement can depend on aspects such as the cost of the component, and the labor rates, but there are good quality OE suitable replacements at reasonable prices. Installation is another critical factor during assembly since it minimizes mechanical problems, and hence makes the Wheel Hub valuable for a vehicle.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Nitro Wheel Hub at great affordable prices. Moreover, all genuine Dodge Nitro Wheel Hub come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Nitro Wheel Hub Parts Questions & Experts Answers

Wheel Hub Front
52109947AD
Q: How to remove and replace a Wheel Hub and bearing assembly on Dodge Nitro?
A:
The hub and bearing assembly cannot be disassembled and must be replaced if either component is damaged or worn. To remove the assembly, start by removing the wheel center cap/hubcap on 4WD models. Loosen the drive axle/hub nut and the front wheel lug nuts. Raise the front of the vehicle and secure it on jack stands. Remove the wheel, disc brake caliper, caliper mounting bracket, brake disc, ABS wheel speed sensor, and sensor wire bracket. On 4WD models, remove the axle hub nut. Unbolt the hub assembly from the steering knuckle and tap it out of the knuckle bore. If the drive axle sticks in the hub splines, use a puller to push it out. To install the new hub assembly, clean the opening in the steering knuckle and attach the assembly, tightening the hub-to-knuckle bolts securely. On 4WD models, install and tighten the hub nut. Complete the installation by following the reverse steps of removal. Lower the vehicle and tighten the hub nut and lug nuts to the specified torque.