How to remove and install the door trim panel and window regulator on Dodge Nitro?

Remove the door trim panel and water shield. For 2007 and earlier models, detach the glass from the regulator, noting that the glass does not need to be completely removed; it can be temporarily held in the up position with strong tape. Loosen the window regulator-to-door attaching bolts, disconnect the runout tube clip, and then remove the regulator. For power windows, disconnect the wiring and remove the regulator from the door. Installation is the reverse of removal, ensuring all fasteners are tightened in the proper sequence. For 2008 and later models, note that the window regulator is an integral component of the door module, and if there is a problem, the door module must be replaced. Remove the access plug from the door, then work through the access hole to remove the outside door handle mounting nut. Remove the window, the three latch fasteners from the end of the door, and the latch-to-door face mounting screw. Disconnect the main harness connector at the front edge of the door, remove the door module mounting screws from around the perimeter of the module, and disconnect the outside mirror electrical connector. Maneuver the module assembly out of the door body, and for installation, ensure the door lock cylinder is aligned and engaged with the door module before installing the module mounting bolts.

Genuine Dodge Nitro Window Regulator

Electric Power Window Regulator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Window Regulators found

View related parts
Dodge Nitro Front Door Window Regulator
Part Number: 68027665AA
$435.48 MSRP: $638.00
You Save: $202.52 (32%)
ADD TO CART
Product Specifications
- Other Name: Regulator Front Door Window With Carrier Plate With Motor; Window Regulator
- Position: Front
- Replaced by: 68027665AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Front Door Window Regulator
Part Number: 68004820AA
$210.10 MSRP: $380.00
You Save: $169.90 (45%)
ADD TO CART
Product Specifications
- Other Name: Regulator Front Door Window With Carrier Plate With Motor; Window Regulator
- Position: Passenger Side
- Replaced by:
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Door Window Regulator
Part Number: 68004822AA
$380.76 MSRP: $559.00
You Save: $178.24 (32%)
Product Specifications
- Other Name: Regulator Rear Door Window With Carrier Plate; Window Regulator
- Position: Passenger Side
- Replaced by:
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Front Door Window Regulator
Part Number: 68027664AA
Product Specifications
- Other Name: Regulator Front Door Window With Carrier Plate With Motor; Window Regulator
- Position: Front
- Replaced by: 68027664AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Rear Door Window Regulator
Part Number: 68004823AA
Product Specifications
- Other Name: Regulator Rear Door Window With Carrier Plate; Window Regulator
- Position: Driver Side
- Replaced by:
- Replaces: 68043559AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L
View related parts
Dodge Nitro Front Door Window Regulator
Part Number: 68004821AA
Product Specifications
- Other Name: Regulator Front Door Window With Carrier Plate With Motor; Window Regulator
- Position: Driver Side
- Replaced by:
- Replaces: 68043558AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2011 Dodge Nitro | Detonator 2WD, Detonator 4WD, Heat 2WD, Heat 4WD, SE 2WD, SE 4WD, Shock 2WD, Shock 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 6 Cyl 4.0L

Dodge Nitro Window Regulator

The concern here is the performance of the Window Regulator used in Dodge Nitro cars in one of its basic roles, to up and down control of the windows for occupants. These regulators can be electric motor driven or swung manually through the use of a crank depending on the model in consideration. Several components involved within the Dodge Nitro Window Regulator design are scissor type or cable type that can offer efficient operation to hold the glass safely. As expected, Dodge Nitro Window Regulators are often used and thus can tearage or have other problems such as the window getting stuck. To solve such problems, the Quality Replacement Window Regulators are manufactured to fit and work as the Original Equipment Manufacturers intended. Dodge Nitro owners can fix crank window regulators which helps in improving the ease in using their car's windows thus increasing the car's comfort.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Nitro Window Regulator at great affordable prices. Moreover, all genuine Dodge Nitro Window Regulator come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Nitro Window Regulator Parts Questions & Experts Answers

Door Window Regulator
68004822AA
Q:
How to remove and install the door trim panel and window regulator on Dodge Nitro?
A:
Remove the door trim panel and water shield. For 2007 and earlier models, detach the glass from the regulator, noting that the glass does not need to be completely removed; it can be temporarily held in the up position with strong tape. Loosen the window regulator-to-door attaching bolts, disconnect the runout tube clip, and then remove the regulator. For power windows, disconnect the wiring and remove the regulator from the door. Installation is the reverse of removal, ensuring all fasteners are tightened in the proper sequence. For 2008 and later models, note that the window regulator is an integral component of the door module, and if there is a problem, the door module must be replaced. Remove the access plug from the door, then work through the access hole to remove the outside door handle mounting nut. Remove the window, the three latch fasteners from the end of the door, and the latch-to-door face mounting screw. Disconnect the main harness connector at the front edge of the door, remove the door module mounting screws from around the perimeter of the module, and disconnect the outside mirror electrical connector. Maneuver the module assembly out of the door body, and for installation, ensure the Door Lock Cylinder is aligned and engaged with the door module before installing the module mounting bolts.