How to adjust the brake light switch on a Jeep Cherokee?

Disconnect the cable from the negative terminal of the battery. From under the dash, unplug the brake light switch electrical connector and remove the pushrod bolt. Remove the brake light switch, noting the positions of the bushings, spacers and sleeves. Lubricate the switch bushings, spacers and sleeves with a light coat of multi-purpose grease and position the switch against the brake pedal. Install the pushrod bolt from the correct side and install the nuts, tightening them to the specified torque. Attach the electrical connector and reconnect the battery. The switch is not adjustable. On pre-1991 models, the switch is not adjustable. On 1991 and later models, it is adjustable. To check the switch adjustment on 1991 and later models, move the brake pedal forward by hand and watch the switch plunger. It should be fully extended at the point at which pedal free play is taken up and brake application begins. A clearance of about 1/8-inch should exist between the plunger and the pedal at this point. If the plunger-to-pedal clearance is correct and the brake lights are operating, no adjustment is necessary. If the plunger doesn't fully extend and the clearance between the pedal and switch barrel is insufficient, adjust the switch. To adjust the switch, grasp the brake pedal and pull it to the rear as far as possible. The switch plunger barrel will "ratchet" to the rear in its retaining clip to the correct position. Measure the plunger-to-pedal clearance to make sure it's correct and verify that the brake lights are still operating correctly. Warning: Make SURE the brake pedal returns to its fully released position after adjustment. The switch can interfere with full pedal return if it's too far forward, resulting in dragging brakes caused by partial brake application.

Genuine Jeep Cherokee Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Light Switches found

View related parts
Jeep Cherokee Stop Lamp Switch
Part Number: 4671336
$42.65 MSRP: $58.00
You Save: $15.35 (27%)
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp
- Replaced by: 4671336AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2001 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4 Door Sport Utility RHD 2WD, 4 Door Sport Utility RHD 4WD, Classic 4 Door 2WD, Classic 4 Door 4WD, Limited 4 Door 2WD, Limited 4 Door 4WD, SE 2 Door 2WD, SE 2 Door 4WD, SE 4 Door 2WD, SE 4 Door 4WD, SE RHD 4 Door 2WD, SE RHD 4 Door 4WD, Sport 2 Door 2WD, Sport 2 Door 4WD, Sport 4 Door 2WD, Sport 4 Door 4WD | 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Cherokee Stop Lamp Switch
Part Number: 56038958AA
$21.67 MSRP: $31.00
You Save: $9.33 (31%)
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp
- Replaced by: 68349583AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2016 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L, 6 Cyl 3.2L
View related parts
Jeep Cherokee Stop Lamp Switch
Part Number: 56038958AC
$21.67 MSRP: $31.00
You Save: $9.33 (31%)
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp
- Replaced by: 68349583AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L, 6 Cyl 3.2L
View related parts
Jeep Cherokee Stop Lamp Switch
Part Number: 68349583AA
$21.67 MSRP: $31.00
You Save: $9.33 (31%)
ADD TO CART
Product Specifications
- Other Name: Switch-Stop Lamp; Lamp Switch, Stoplamp Switch
- Replaces: 56038958AA, 56038958AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Lux AWD, Latitude Lux FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L, 4 Cyl 2.4 L GAS, 4 Cyl 2.4L, 6 Cyl 3.2 L GAS, 6 Cyl 3.2L
View related parts
Jeep Cherokee Switch, Brake Lamp
Part Number: J3225787
Product Specifications
- Other Name: Stoplamp Switch, Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1990 Jeep Cherokee | 4 Cyl 2.1L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.0L, 6 Cyl 4.2L
View related parts
Jeep Cherokee Switch, Stop Lamp
Part Number: 56006981
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1996 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 2 Door Sport Utility RHD 2WD, 2 Door Sport Utility RHD 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4 Door Sport Utility RHD 2WD, 4 Door Sport Utility RHD 4WD | 4 Cyl 2.1L Diesel, 4 Cyl 2.5L, 4 Cyl 2.5L Diesel, 6 Cyl 4.0L

Jeep Cherokee Brake Light Switch

The Brake Light Switch in Jeep Cherokee is very important since it controls the brake lights whenever the brake pedal is depressed. It also has a function of warning the oncoming traffic whenever the Jeep Cherokee is slowing down or coming to a stand still making the road a safer place. There are different types of Brake Light Switch used in Jeep Cherokee through the years, that is without mentioning the specific ones in the given information. The main emphasis is kept on usage of the investigated switch for signaling the braking actions, and it is again important to mark that it is actual for different generations of Jeep Cherokee. It is evident that the Brake Light Switch plays an important role in conveying signals to other motorists which would in turn enhance road safety.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Cherokee Brake Light Switch at great affordable prices. Moreover, all genuine Jeep Cherokee Brake Light Switch come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Cherokee Brake Light Switch Parts Questions & Experts Answers

Switch, Brake Lamp
J3225787
Q: How to adjust the brake light switch on a Jeep Cherokee?
A:
Disconnect the cable from the negative terminal of the battery. From under the dash, unplug the brake light switch electrical connector and remove the pushrod bolt. Remove the brake light switch, noting the positions of the bushings, spacers and sleeves. Lubricate the switch bushings, spacers and sleeves with a light coat of multi-purpose grease and position the switch against the brake pedal. Install the pushrod bolt from the correct side and install the nuts, tightening them to the specified torque. Attach the electrical connector and reconnect the battery. The switch is not adjustable. On pre-1991 models, the switch is not adjustable. On 1991 and later models, it is adjustable. To check the switch adjustment on 1991 and later models, move the brake pedal forward by hand and watch the switch plunger. It should be fully extended at the point at which pedal free play is taken up and brake application begins. A clearance of about 1/8-inch should exist between the plunger and the pedal at this point. If the plunger-to-pedal clearance is correct and the brake lights are operating, no adjustment is necessary. If the plunger doesn't fully extend and the clearance between the pedal and switch barrel is insufficient, adjust the switch. To adjust the switch, grasp the brake pedal and pull it to the rear as far as possible. The switch plunger barrel will "ratchet" to the rear in its retaining clip to the correct position. Measure the plunger-to-pedal clearance to make sure it's correct and verify that the brake lights are still operating correctly. Warning: Make SURE the brake pedal returns to its fully released position after adjustment. The switch can interfere with full pedal return if it's too far forward, resulting in dragging brakes caused by partial brake application.