How to remove and install the Wheel Bearing and Wheel Hub on Jeep Wrangler?

To dismantle the bearing cap from the hub, you have to first dismantle the cotter pin and nut lock then lessening the axial hub nut. After that, remove the front wheel lug nuts, lift the car front side and put it on the jackstands and then remove the wheel. Carry out the removal of the disc brake caliper and the associated disc, and if required, the ABS speed sensor. Then, loosen the axle hub nut and then unthread the hub assembly from the steering knuckle for which you have to take out the hub assembly using a twelve-point socket, there are three bolt that hold the assembly in the knuckle bore of the steering knuckle. If it is badly stuck in the splines of the hub, get rid of it by a force of the dead blow hammer, but if not try using a puller. For service on early models, hub bearings are usually serviced but because of the special tools and correct techniques involved, it is best to turn over this job to a dealer or repair shop. In later models, the hub and bearing assembly has to be ordered and replaced in one piece; it is advisable to consult a parts catalogue for availability. For installation, it is recommended to smoothen the opening in the steering knuckle using sandpaper or emery cloth in order to remove all rust or dirt and that the axleshaft splines should be coated with wheel bearing grease. Apply grease along the opening that is in the steering knuckle and put the hub assembly then use your wrench or the specified torque to tighten the bolts. Lastly, safely replace the washer and hub nut, then the brake disc, and the caliper, then, the wheel; drop the vehicle and finally, much the lug nuts to the prescribed torque.

Genuine Jeep Wrangler Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Wheel Hubs found

View related parts
Jeep Wrangler Front Brake Hub And Bearing
Part Number: 52060398AE
$259.40 MSRP: $405.00
You Save: $145.60 (36%)
ADD TO CART
Product Specifications
- Other Name: Hub&Bearing-Brake; Front Hub & Bearing, Hub & Bearing
- Position: Front
- Replaces: 52060398AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2018 Jeep Wrangler | 70th Anniversary, Rubicon, Rubicon 4WD, Sahara, Sahara 4WD, Sport, Sport 4WD, Unlimited Rubicon, Unlimited Rubicon 4WD, Unlimited Sahara 4WD, Unlimited Sport 4WD | 6 Cyl 3.6L, 6 Cyl 3.8L
View related parts
Jeep Wrangler Hub And Bearing Assembly
Part Number: 52060398AD
$259.40 MSRP: $405.00
You Save: $145.60 (36%)
ADD TO CART
Product Specifications
- Other Name: Hub And Bearing Brake Front
- Replaced by: 52060398AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Jeep Wrangler | 70th Anniversary, Rubicon, Sahara, Sahara 4WD, Sport, Unlimited Rubicon, Unlimited Sahara 4WD, Unlimited Sport 4WD | 6 Cyl 3.6L, 6 Cyl 3.8L
View related parts
Jeep Wrangler Brake Hub And Bearing
Part Number: 2AMVH398AA
$83.92 MSRP: $148.00
You Save: $64.08 (44%)
ADD TO CART
Product Specifications
- Other Name: Hub&BRG-Brake
- Replaced by: 1BP00254AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Jeep Wrangler | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara 2WD, Unlimited Sahara 4WD, Unlimited Sport 2WD, Unlimited Sport 4WD, Unlimited X 2WD, Unlimited X 4WD, Unlimited X RHD 4WD, X, X RHD | 6 Cyl 3.8L
View related parts
Jeep Wrangler Disc Brake Hub-Wheel Bearing And Hub Assembly Front
Part Number: V2506458AA
$105.47 MSRP: $125.00
You Save: $19.53 (16%)
ADD TO CART
Product Specifications
- Other Name: Hub&Bearing-Brake
- Position: Front
- Replaced by: 1BP00642AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2006 Jeep Wrangler | Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Front Brake Hub And Bearing Assembly
Part Number: V2507449AA
$103.78 MSRP: $123.00
You Save: $19.22 (16%)
ADD TO CART
Product Specifications
- Other Name: Hub And Bearing Assembly, Front Brake
- Replaced by: 1BP00239AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Jeep Wrangler | SE | 4 Cyl 2.5L, 6 Cyl 4.0L
- 1987-1995 Jeep Wrangler | Sport Utility 4WD | 4 Cyl 2.5L, 6 Cyl 4.0L, 6 Cyl 4.2L
View related parts
Jeep Wrangler Front Wheel Hub Bearing Assembly Compatible
Part Number: 53007449AB
$251.49
ADD TO CART
Product Specifications
- Other Name: Hub And Bearing Brake
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999 Jeep Wrangler | SE | 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Brake Hub And Bearing
Part Number: 68272624AC
$209.81 MSRP: $310.00
You Save: $100.19 (33%)
Product Specifications
- Other Name: Hub&BRG-Brake; Front Hub & Bearing, Hub & Bearing
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | Rubicon 4WD, Rubicon Unlimited 4WD, Sahara Unlimited 4WD, Sport 4WD, Sport Unlimited 4WD, Unlimited 4XE 4WD, Unlimited Rubicon 4WD, Unlimited Rubicon 4XE 4WD, Unlimited Sahara 4WD, Unlimited Sahara 4XE 4WD, Unlimited Sport 4WD, Unlimited Sport RHD 4WD | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.0L, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.0L Diesel, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6L, 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Front Hub And Bearing
Part Number: 52060398AC
$213.19 MSRP: $315.00
You Save: $101.81 (33%)
Product Specifications
- Other Name: Hub And Bearing Brake Front; Front Hub & Bearing, Hub & Bearing
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Jeep Wrangler | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara 2WD, Unlimited Sahara 4WD, Unlimited Sport 2WD, Unlimited Sport 4WD, Unlimited X 2WD, Unlimited X 4WD, Unlimited X RHD 4WD, X, X RHD | 6 Cyl 3.8L
View related parts
Jeep Wrangler Front Wheel Hub Bearing Assembly
Part Number: 5016458AA
Product Specifications
- Other Name: Hub And Bearing Brake; Front Hub & Bearing, Hub & Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2006 Jeep Wrangler | Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 4.0L

Jeep Wrangler Wheel Hub

In terms of vehicles, The Wheel Hub of Jeep Wrangler automobiles is a central part that links wheels to cars hence effectively in maintaining stability as well as steering control. Some of the items that are housed inside include wheel bearings, sensors, and brake parts and thus enables the free rotation of the wheels while at the same time firmly fixing the wheels onto the Wrangler. Several configurations of Wheel Hubs have been used on jeep wrangler models in the course of the years, with changes in the bolt circumference and pattern. Due to this it is important to get a direct-fit replacement Wheel Hub that suits the needs of the Jeep Wrangler as much as possible. The proper installation of the assembly especially requires application of torque so as to avoid mechanical problems and this makes the Wheel Hub very crucial for the reliability and safety of the vehicle.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Wrangler Wheel Hub at great affordable prices. Moreover, all genuine Jeep Wrangler Wheel Hub come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Wrangler Wheel Hub Parts Questions & Experts Answers

Disc Brake Hub-Wheel Bearing And Hub Assembly Front
V2506458AA
Q: How to remove and install the Wheel Bearing and Wheel Hub on Jeep Wrangler?
A:
To dismantle the bearing cap from the hub, you have to first dismantle the cotter pin and nut lock then lessening the axial hub nut. After that, remove the front wheel lug nuts, lift the car front side and put it on the jackstands and then remove the wheel. Carry out the removal of the disc brake caliper and the associated disc, and if required, the ABS speed sensor. Then, loosen the axle hub nut and then unthread the hub assembly from the steering knuckle for which you have to take out the hub assembly using a twelve-point socket, there are three bolt that hold the assembly in the knuckle bore of the steering knuckle. If it is badly stuck in the splines of the hub, get rid of it by a force of the dead blow hammer, but if not try using a puller. For service on early models, hub bearings are usually serviced but because of the special tools and correct techniques involved, it is best to turn over this job to a dealer or repair shop. In later models, the hub and bearing assembly has to be ordered and replaced in one piece; it is advisable to consult a parts catalogue for availability. For installation, it is recommended to smoothen the opening in the steering knuckle using sandpaper or emery cloth in order to remove all rust or dirt and that the axleshaft splines should be coated with wheel bearing grease. Apply grease along the opening that is in the steering knuckle and put the hub assembly then use your wrench or the specified torque to tighten the bolts. Lastly, safely replace the washer and hub nut, then the brake disc, and the caliper, then, the wheel; drop the vehicle and finally, much the lug nuts to the prescribed torque.