My Garage
My Account
Cart
Genuine Chrysler 200 Timing Chain
Engine Timing Chain- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
6 Timing Chains found
Chrysler 200 Chain-Timing Secondary
Part Number: 5184352AF$174.38 MSRP: $259.00You Save: $84.62 (33%)
Chrysler 200 Timing Chain
The Chrysler 200 automobile product features a timing chain that principally assist in aligning the crankshaft and camshaft in order to enable right time for valve regulating, crucial for an automobile engine. Located at the front of the engine, the Timing Chain needs lubrication, it is usually applied to higher-displacement engines. The Chrysler 200 models have applied the metal timing chains that have become popular since the 1990s because of the effectiveness of the metal chains and their less frequent replacements as it compared to the rubber timing belts. Although these Timing Chains are worn proof, the problems may occur due to absence of lubrication, failure of tensioner and chain guides that may can manifest themselves by a rattling noise coming from the engine. Another advantage of the pushrod configurations is that it utilizes a short chain to reduce noise and wear and therefore ideal for Chrysler 200.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler 200 Timing Chain at great affordable prices. Moreover, all genuine Chrysler 200 Timing Chain come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Chrysler 200 Timing Chain Parts Questions & Experts Answers
- Q: How to remove and install Timing Chain and Oil Pump in four cylinder engine on Chrysler 200?A:The oil pump is an integral component of the balance shaft module and cannot be removed or disassembled from it; if there is a problem with the oil pump, the entire balance shaft module must be replaced. To begin removal, relieve the fuel system pressure and disconnect the negative battery cable from the remote ground terminal or battery. Rotate the engine to Top Dead Center for the #1 cylinder on the compression stroke. Loosen the lug nuts on the right front wheel, raise the vehicle, and support it securely on jackstands. Remove the right front wheel, splash shield, and inner fender shield, followed by the valve cover and Oil Pan. Next, remove the timing chain cover, timing chain, and crankshaft sprocket. Align the drive chain plated links with the timing marks on the crankshaft sprocket and the Balance Shaft Module drive gear; if the marks cannot be found, mark the oil pump/Balance Shaft Module drive chain to the BSM drive sprocket and crankshaft gear for proper installation. Press the oil pump/BSM tensioner piston back into the tensioner body, retaining it in the locked position with a special tool or a 3 mm drill bit. Do not remove the oil pump/BSM drive sprocket. Remove the BSM mounting bolts in reverse order of tightening, lowering the rear of the balance shaft module, removing the timing chain from the sprocket, and then the BSM itself. Remove the chain from the crankshaft sprocket. If necessary, replace the crankshaft front seal within the oil pump body. Two different lengths of mounting bolts can be used on the BSM: 180 mm and 185 mm; discard the 180 mm bolts and replace them with new ones, measuring the BSM mounting bolts and replacing as needed. Check the threads of each 185 mm mounting bolt with a straightedge or ruler; if there is a gap, replace the bolts and apply clean engine oil to the threads before installation. Clean the bolt holes for the BSM mounting bolts, then place the timing chain over the crankshaft sprocket, aligning the plated link with the timing mark or previously made marks. Lift the BSM and place the drive sprocket into the timing chain, aligning the plated link with the timing mark on the drive gear. While holding the BSM in place, insert the mounting bolts and tighten by hand in several even stages, then tighten the bolts in the recommended sequence to the specified torque. The final step requires tightening the bolts a specific number of degrees; an angle-torque gauge is recommended for this procedure. After tightening, remove the pin from the tensioner and release the piston, verifying that the timing marks are aligned. Install the timing chain and Timing Cover, followed by the oil pan and valve cover. The remainder of the installation follows the reverse order of removal. Finally, install a new oil filter and engine oil, start the engine, check for oil pressure and leaks, and recheck the engine oil level.
