How to check and replace the Cooling Fan Assembly and Engine Cooling Fan on Dodge Dakota?

When your fan clutch malfunctions, it makes constant loud noises, shakes, and leaks silicone fluid. Test a cold car's engine by shaking the fan with your hands in two directions. If the bearing moves too much, the fan should spin easily when you turn the blades. Check for significant transmission fluid loss, damaged heat-dispersion spring, and lubricant leakage from fan motor bearings by sight. Replace fan gear assembly if any signs of these problems appear. With the engine running and hot enough to get to standard operating temperature, stop the engine. Hold onto the fan while turning by hand; if it turns with some effort, change the fan clutch. Replace cooling fans and fan clutches that have REVERSE on their label. This is because certain engine models run their fans backward and only non-reverse parts can prevent overheating in those models. Place the cooling fan/viscous fan clutch assembly in an upright position to keep hydraulic fluids from leaking into the bearing section. First, lower the cooling system water level, take off the top radiator hose, and grasp the pump pulley with a special pin removal tool while turning the fan clutch nut loose with a big open-end wrench. An average person can probably keep the water pump pulley in place by using hand pressure on the belt. You might need to use a special tool, though, if the fan drive nut is already too tight to move. First, turn the nut left by hand until the fan and clutch are loose. Put your assembly and clutch gently into the shroud, being careful not to touch the radiator fins. Pull off the clips that hold the fan shroud to the car body, disconnect any bottom clips that attached there, and then take out the fan shroud, still fastened to the cooling fan. To take down the cooling fan, loosen the bolts that hold the fan clutch to the viscous fan, put everything back together keeping the fan nut fastened and fan bolts done correctly.

Genuine Dodge Dakota Engine Cooling Fan

Radiator Fan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Engine Cooling Fans found

View related parts
Dodge Dakota Clutch
Part Number: 52029288AB
Product Specifications
- Other Name: Fan; Cooling Fan, Fan Blade
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2011 Dodge Dakota | Laramie Club Cab 2WD, Laramie Club Cab 4WD, Laramie Crew Cab 2WD, Laramie Crew Cab 4WD, Laramie Quad Cab 2WD, Laramie Quad Cab 4WD, SLT Club Cab 2WD, SLT Club Cab 4WD, SLT Crew Cab 2WD, SLT Crew Cab 4WD, SLT Extended Cab 2WD, SLT Extended Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, Sport Crew Cab 2WD, Sport Crew Cab 4WD, ST Club Cab 2WD, ST Club Cab 4WD, ST Crew Cab 2WD, ST Crew Cab 4WD, ST Extended Cab 2WD, ST Extended Cab 4WD, ST Quad Cab 2WD, ST Quad Cab 4WD, SXT Crew Cab 2WD, SXT Crew Cab 4WD, TRX Crew Cab 2WD, TRX Crew Cab 4WD | 6 Cyl 3.7L, 8 Cyl 4.7L
View related parts
Dodge Dakota Cooling Fan
Part Number: 55056414AA
Product Specifications
- Other Name: Fan Cooling; Fan Blade
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Dodge Dakota | Club Cab 2WD, Club Cab 4WD, Regular Cab 2WD, Regular Cab 4WD, SLT Club Cab 2WD, SLT Club Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, Sport Club Cab 2WD, Sport Club Cab 4WD, Sport Quad Cab 2WD, Sport Quad Cab 4WD, Sport Regular Cab 2WD, Sport Regular Cab 4WD | 6 Cyl 3.9L
View related parts
Dodge Dakota Cooling Fan
Part Number: 52029263AB
Product Specifications
- Other Name: Fan Cooling
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Dodge Dakota | Club Cab 2WD, Club Cab 4WD, Quad Cab 2WD, Quad Cab 4WD, Regular Cab 2WD, Regular Cab 4WD, SLT Club Cab 2WD, SLT Club Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, Sport Club Cab 2WD, Sport Club Cab 4WD, Sport Quad Cab 2WD, Sport Quad Cab 4WD, Sport Regular Cab 2WD, Sport Regular Cab 4WD | 6 Cyl 3.9L
View related parts
Dodge Dakota Cooling Fan
Part Number: 52028916AB
Product Specifications
- Other Name: Fan Cooling
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2003 Dodge Dakota | Club Cab 2WD, Club Cab 4WD, Quad Cab 2WD, Quad Cab 4WD, R/T Club Cab 2WD, R/T Regular Cab 2WD, Regular Cab 2WD, Regular Cab 4WD, SLT Club Cab 2WD, SLT Club Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, Sport Club Cab 2WD, Sport Club Cab 4WD, Sport Quad Cab 2WD, Sport Quad Cab 4WD, Sport Regular Cab 2WD, Sport Regular Cab 4WD | 8 Cyl 4.7L, 8 Cyl 5.9L
View related parts
Dodge Dakota Cooling Fan
Part Number: 52028756AA
Product Specifications
- Other Name: Fan Cooling
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Dodge Dakota | Club Cab 2WD, Club Cab 4WD, Regular Cab 2WD, Regular Cab 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Dakota Cooling Fan
Part Number: 52027999
Product Specifications
- Other Name: Fan Cooling
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Dodge Dakota | 3-Person Cab 2WD, 3-Person Cab 4WD, Club Cab 2WD, Club Cab 4WD, Regular Cab 2WD, Regular Cab 4WD | 6 Cyl 3.9L, 8 Cyl 5.2L
View related parts
Dodge Dakota Cooling Fan
Part Number: 52029263AC
Product Specifications
- Other Name: Fan Cooling; Fan Blade
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Dakota | Club Cab 4WD, Regular Cab 4WD, SLT Club Cab 4WD, SLT Quad Cab 4WD, SLT Regular Cab 4WD, Sport Club Cab 4WD, Sport Quad Cab 4WD, Sport Regular Cab 4WD | 6 Cyl 3.7L
View related parts
Dodge Dakota Radiator Cooling Fan
Part Number: 52030033AD
Product Specifications
- Other Name: Fan Module Radiator Cooling Electric
- Replaces: 52030033AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2004 Dodge Dakota | Club Cab 2WD, Club Cab 4WD, R/T Club Cab 2WD, R/T Regular Cab 2WD, Regular Cab 2WD, Regular Cab 4WD, SLT Club Cab 2WD, SLT Club Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, Sport Club Cab 2WD, Sport Club Cab 4WD, Sport Quad Cab 2WD, Sport Quad Cab 4WD, Sport Regular Cab 2WD, Sport Regular Cab 4WD | 6 Cyl 3.7L, 6 Cyl 3.9L, 8 Cyl 4.7L, 8 Cyl 5.9L
View related parts
Dodge Dakota Cooling Fan
Part Number: 52028916AC
Product Specifications
- Other Name: Fan Cooling; Fan Blade, Transmission Cooler
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Dakota | Club Cab 2WD, Club Cab 4WD, Regular Cab 2WD, Regular Cab 4WD, SLT Club Cab 2WD, SLT Club Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, Sport Club Cab 2WD, Sport Club Cab 4WD, Sport Quad Cab 2WD, Sport Quad Cab 4WD, Sport Regular Cab 2WD, Sport Regular Cab 4WD | 6 Cyl 3.7L, 8 Cyl 4.7L

Dodge Dakota Engine Cooling Fan

Is the Dodge Dakota Engine Cooling Fan necessary? Well, yes, it is in fact very essential. How else would your mid-size truck's powerplant stay within the safe limits of temperature? It activates when forward motion alone cannot create enough airflow to provide fresh air through the radiator. When driving on the highway, ram air through the grille cools the radiator core. However, at idle or in traffic, the fan takes over, pulling air across the fins so that the heat leaves the fluid before it goes back to the engine. The early Dodge Dakota trucks featured a mechanical Engine Cooling Fan that was bolted to the water pump. This fan spun any time the engine was running. In addition, a thermostatic clutch limited the drag when temperatures were not high. In line with changes in design, the Dodge Dakota platform adopted an electric Engine Cooling Fan equipped with a compact motor, curved blades, and a shroud that provided precise control for the computer while freeing up horsepower. The purpose of both versions is the same, and the electric version of the Engine Cooling Fan responds quicker, operates only when necessary, and emits less noise compared to the turning mechanical unit. The Engine Cooling Fan pulls cool air through the radiator to avoid overheating in traffic and while towing. This keeps every Dodge Dakota safer.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Dakota Engine Cooling Fan at great affordable prices. Moreover, all genuine Dodge Dakota Engine Cooling Fan come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Dakota Engine Cooling Fan Parts Questions & Experts Answers

Clutch
52029288AB
Q: How to check and replace the Cooling Fan Assembly and Engine Cooling Fan on Dodge Dakota?
A:
When your fan clutch malfunctions, it makes constant loud noises, shakes, and leaks silicone fluid. Test a cold car's engine by shaking the fan with your hands in two directions. If the bearing moves too much, the fan should spin easily when you turn the blades. Check for significant transmission fluid loss, damaged heat-dispersion spring, and lubricant leakage from fan motor bearings by sight. Replace fan gear assembly if any signs of these problems appear. With the engine running and hot enough to get to standard operating temperature, stop the engine. Hold onto the fan while turning by hand; if it turns with some effort, change the fan clutch. Replace cooling fans and fan clutches that have REVERSE on their label. This is because certain engine models run their fans backward and only non-reverse parts can prevent overheating in those models. Place the cooling fan/viscous fan clutch assembly in an upright position to keep hydraulic fluids from leaking into the bearing section. First, lower the cooling system water level, take off the top radiator hose, and grasp the pump pulley with a special pin removal tool while turning the fan clutch nut loose with a big open-end wrench. An average person can probably keep the water pump pulley in place by using hand pressure on the belt. You might need to use a special tool, though, if the fan drive nut is already too tight to move. First, turn the nut left by hand until the fan and clutch are loose. Put your assembly and clutch gently into the shroud, being careful not to touch the radiator fins. Pull off the clips that hold the fan shroud to the car body, disconnect any bottom clips that attached there, and then take out the fan shroud, still fastened to the cooling fan. To take down the cooling fan, loosen the bolts that hold the fan clutch to the viscous fan, put everything back together keeping the fan nut fastened and fan bolts done correctly.