What are the ways to check the operation of the water pump while it's installed on the engine on Jeep Cherokee?

A faulty water pump can cause engine damage due to overheating. Three ways to check the pump are: squeezing the upper radiator hose while the engine is running at normal temperature, a pressure surge should be felt if the pump is working; checking the weep or vent holes for coolant leaks, a flashlight may be needed; and listening for a howling sound at the engine front, indicating shaft bearing failure. Shaft wear can also be detected by rocking the water pump pulley. Don't confuse drivebelt slippage, which causes a squealing sound, with water pump failure.

How to replace a water pump in a Jeep Cherokee?

Disconnect the negative battery cable from the battery. Drain the cooling system. If the coolant is relatively new or in good condition, save it and reuse it. Remove the cooling fan and shroud. On inline six-cylinder engines, loosen the pulley-to-water pump bolts and remove the drivebelts and the pulley at the end of the water pump shaft. Loosen the clamps and detach the hoses from the water pump. If they're stuck, grasp each hose near the end with a pair of Channelock pliers and twist it to break the seal, then pull it off. If the hoses are deteriorated, cut them off and install new ones. Remove all accessory brackets from the water pump. When removing the power steering pump and air conditioning compressor, don't disconnect the hoses. Tie the units aside with the hoses attached. Keep the power steering pump upright so fluid doesn't spill. Remove the bolts and detach the water pump from the engine. Note the locations of the various lengths and different types of bolts as they're removed to ensure correct installation. Clean the bolt threads and the threaded holes in the engine to remove corrosion and sealant. Compare the new pump to the old one to make sure they're identical. Remove all traces of old gasket material from the engine with a gasket scraper. Clean the engine and new water pump mating surfaces with lacquer thinner or acetone. Apply a thin coat of RTV sealant to the engine side of the new gasket. Apply a thin layer of RTV sealant to the gasket mating surface of the new pump, then carefully mate the gasket and the pump. Slip a couple of bolts through the pump mounting holes to hold the gasket in place. Carefully attach the pump and gasket to the engine and thread the bolts into the holes finger tight. Install the remaining bolts and tighten them to the specified torque in 1/4-turn increments. Note that the three sizes of bolts on V6 engines require different torques. Don't overtighten them or the pump may be distorted. Reinstall all parts removed for access to the pump. Refill the cooling system and check the drivebelt tension. Run the engine and check for leaks.

Genuine Jeep Cherokee Water Pump

H2O Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Water Pumps found

View related parts
Jeep Cherokee Auxiliary Coolant Pump
Part Number: 68259097AB
$292.13 MSRP: $442.00
You Save: $149.87 (34%)
ADD TO CART
Product Specifications
- Other Name: Pump-Auxiliary Coolant; Auxiliary Pump, Water Pump
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2019-2023 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Lux AWD, Latitude Lux FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Trailhawk AWD | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Water Pump
Part Number: 68286387AA
$183.38 MSRP: $274.00
You Save: $90.62 (34%)
ADD TO CART
Product Specifications
- Other Name: Pump-Water
- Replaced by: 68527417AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2019-2020 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Trailhawk AWD
View related parts
Jeep Cherokee Engine Cooling Water Pump
Part Number: 4626054AD
$257.57 MSRP: $387.00
You Save: $129.43 (34%)
ADD TO CART
Product Specifications
- Other Name: Pump Package Water
- Replaced by: 68382489AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, SE 2 Door 2WD, SE 2 Door 4WD, SE 4 Door 2WD, SE 4 Door 4WD | 4 Cyl 2.5L
View related parts
Jeep Cherokee Water Pump
Part Number: 68111624AF
$146.56 MSRP: $216.00
You Save: $69.44 (33%)
ADD TO CART
Product Specifications
- Other Name: Pump-Water; Water Pump Assembly
- Replaced by: 68667065AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2021 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Lux AWD, Latitude Lux FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Trailhawk AWD | 6 Cyl 3.2L
View related parts
Jeep Cherokee Water Pump
Part Number: 83503407
$88.21 MSRP: $131.00
You Save: $42.79 (33%)
ADD TO CART
Product Specifications
- Other Name: Pump Package, Water
- Replaced by: 4626215
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1990 Jeep Cherokee | 4 Cyl 2.1L Diesel, 4 Cyl 2.5L, 6 Cyl 4.0L, 6 Cyl 4.2L
View related parts
Jeep Cherokee Pump-Water
Part Number: 5047389AC
$201.30 MSRP: $301.00
You Save: $99.70 (34%)
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, Water Pump, Water Pump Assembly
- Replaces: 5047389AA, 5047389AB, RL047389AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Lux AWD, Latitude Lux FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 4 Cyl 2.4L, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee WATER
Part Number: 68111624AG
$146.18 MSRP: $216.00
You Save: $69.82 (33%)
ADD TO CART
Product Specifications
- Other Name: Water Pump, Water Pump Assembly
- Replaced by: 68667065AA
- Replaces: 68111624AD, 68111624AF, 68111624AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Cherokee | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Water Pump
Part Number: 68308692AA
$61.59 MSRP: $91.40
You Save: $29.81 (33%)
ADD TO CART
Product Specifications
- Other Name: Pump-Water
- Replaced by: 68640986AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2018 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD
View related parts
Jeep Cherokee Water Pump
Part Number: 68111624AE
$146.56 MSRP: $216.00
You Save: $69.44 (33%)
ADD TO CART
Product Specifications
- Other Name: Pump-Water
- Replaced by: 68667065AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2019 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 6 Cyl 3.2L
View related parts
Jeep Cherokee Water Pump
Part Number: 5047389AA
$201.30 MSRP: $301.00
You Save: $99.70 (34%)
ADD TO CART
Product Specifications
- Other Name: Pump-Water
- Replaced by: 5047389AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2016 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Engine Water Pump
Part Number: 5047389AB
$201.30 MSRP: $301.00
You Save: $99.70 (34%)
ADD TO CART
Product Specifications
- Other Name: Pump-Water
- Replaced by: 5047389AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Auxiliary Coolant Pump
Part Number: 68342102AC
$127.46 MSRP: $190.00
You Save: $62.54 (33%)
ADD TO CART
Product Specifications
- Other Name: Pump-Auxiliary Coolant
- Replaces: 68342102AB, 68523828AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2019-2020 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Trailhawk AWD
View related parts
Jeep Cherokee Water Pump
Part Number: 68046026AA
$73.32 MSRP: $111.00
You Save: $37.68 (34%)
Product Specifications
- Other Name: Pump-Water
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2020 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Engine Cooling Water Pump
Part Number: 4626215AE
$83.19 MSRP: $123.00
You Save: $39.81 (33%)
Product Specifications
- Other Name: Pump Package Water
- Replaced by: 4626215AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001 Jeep Cherokee | Classic 4 Door 2WD, Classic 4 Door 4WD, Limited 4 Door 2WD, Limited 4 Door 4WD, SE 2 Door 2WD, SE 2 Door 4WD, SE 4 Door 2WD, SE 4 Door 4WD, SE RHD 4 Door 2WD, SE RHD 4 Door 4WD, Sport 2 Door 2WD, Sport 2 Door 4WD, Sport 4 Door 2WD, Sport 4 Door 4WD | 6 Cyl 4.0L
View related parts
Jeep Cherokee Package, Water Pump
Part Number: 4626215
$88.21 MSRP: $131.00
You Save: $42.79 (33%)
Product Specifications
- Replaces: 83503407
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1998 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 2 Door Sport Utility RHD 2WD, 2 Door Sport Utility RHD 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4 Door Sport Utility RHD 2WD, 4 Door Sport Utility RHD 4WD | 4 Cyl 2.1L Diesel, 4 Cyl 2.5L, 6 Cyl 4.0L, 6 Cyl 4.2L
View related parts
Jeep Cherokee Water Pump Engine
Part Number: 68111624AD
$146.56 MSRP: $216.00
You Save: $69.44 (33%)
Product Specifications
- Other Name: Pump-Water
- Replaced by: 68667065AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2016 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 6 Cyl 3.2L
View related parts
Jeep Cherokee Pump-Water
Part Number: 4893618AC
$413.73 MSRP: $607.00
You Save: $193.27 (32%)
Product Specifications
- Replaced by: 68657003AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2019 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Trailhawk AWD | 4 Cyl 2.0L
View related parts
Jeep Cherokee Pump Package, Water
Part Number: JR775047
Product Specifications
- Other Name: Water Pump, Water Pump Assembly
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1990 Jeep Cherokee | 4 Cyl 2.1L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.0L, 6 Cyl 4.2L
View related parts
Jeep Cherokee Pump, Water
Part Number: R4626054
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1997 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 2 Door Sport Utility RHD 2WD, 2 Door Sport Utility RHD 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4 Door Sport Utility RHD 2WD, 4 Door Sport Utility RHD 4WD | 4 Cyl 2.1L Diesel, 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Cherokee Water Pump
Part Number: R4626215
Product Specifications
- Other Name: Pump Package, Water
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1998 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 2 Door Sport Utility RHD 2WD, 2 Door Sport Utility RHD 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4 Door Sport Utility RHD 2WD, 4 Door Sport Utility RHD 4WD | 4 Cyl 2.1L Diesel, 4 Cyl 2.5L, 6 Cyl 4.0L, 6 Cyl 4.2L

| Page 1 of 2 |Next >

1-20 of 25 Results

Jeep Cherokee Water Pump

The Water Pump in Jeep Cherokee Cars is one of the vital vehicle parts that pumps coolant from the Radiator to the Engine where it evaporates heat produced during burning. The contemporary water pumps are mainly of Aluminium with a rotating shaft supported by a pair of bearings with an impeller in-between that drives the coolant. Some signs of a faulty water pump are: signs of leakage for the coolant, noises that emanate from the bearings of the water pump, and signs of possible engine overheating. For the high-performance engines, efficient water pumps are designed and these pumps deliver high coolant flow and consume less power. Electric water pumps are also available, which offers such benefits like coolant circulation that is independent of the engine's revolutions, as well as cooling after the engine has been turned off.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Cherokee Water Pump at great affordable prices. Moreover, all genuine Jeep Cherokee Water Pump come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Cherokee Water Pump Parts Questions & Experts Answers

Package, Water Pump
4626215
Q: What are the ways to check the operation of the water pump while it's installed on the engine on Jeep Cherokee?
A: A faulty water pump can cause engine damage due to overheating. Three ways to check the pump are: squeezing the upper radiator hose while the engine is running at normal temperature, a pressure surge should be felt if the pump is working; checking the weep or vent holes for coolant leaks, a flashlight may be needed; and listening for a howling sound at the engine front, indicating shaft bearing failure. Shaft wear can also be detected by rocking the water pump pulley. Don't confuse drivebelt slippage, which causes a squealing sound, with water pump failure.
Engine Cooling Water Pump
4626054AD
Q: How to replace a water pump in a Jeep Cherokee?
A: Disconnect the negative battery cable from the battery. Drain the cooling system. If the coolant is relatively new or in good condition, save it and reuse it. Remove the cooling fan and shroud. On inline six-cylinder engines, loosen the pulley-to-water pump bolts and remove the drivebelts and the pulley at the end of the water pump shaft. Loosen the clamps and detach the hoses from the water pump. If they're stuck, grasp each hose near the end with a pair of Channelock pliers and twist it to break the seal, then pull it off. If the hoses are deteriorated, cut them off and install new ones. Remove all accessory brackets from the water pump. When removing the power steering pump and air conditioning compressor, don't disconnect the hoses. Tie the units aside with the hoses attached. Keep the power steering pump upright so fluid doesn't spill. Remove the bolts and detach the water pump from the engine. Note the locations of the various lengths and different types of bolts as they're removed to ensure correct installation. Clean the bolt threads and the threaded holes in the engine to remove corrosion and sealant. Compare the new pump to the old one to make sure they're identical. Remove all traces of old gasket material from the engine with a gasket scraper. Clean the engine and new water pump mating surfaces with lacquer thinner or acetone. Apply a thin coat of RTV sealant to the engine side of the new gasket. Apply a thin layer of RTV sealant to the gasket mating surface of the new pump, then carefully mate the gasket and the pump. Slip a couple of bolts through the pump mounting holes to hold the gasket in place. Carefully attach the pump and gasket to the engine and thread the bolts into the holes finger tight. Install the remaining bolts and tighten them to the specified torque in 1/4-turn increments. Note that the three sizes of bolts on V6 engines require different torques. Don't overtighten them or the pump may be distorted. Reinstall all parts removed for access to the pump. Refill the cooling system and check the drivebelt tension. Run the engine and check for leaks.