My Garage
My Account
Cart
Genuine Jeep Wrangler PCV Valve
Position Crank Ventilation Valve- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
12 PCV Valves found
Jeep Wrangler PCV Valve
The PCV Valve in Jeep Wrangler cars are essential components that play the role of regulating emission and performance of the automobile's engines. The PCV Valve works to cause a rerouting of the crankcase combustion byproduct gases towards the engine's combustion chambers in order to promote efficient operation and at the same time minimize emissions. Switching its operations on the basis of intake manifold vacuum conditions, the PCV Valve only restricts the flow of gases at idle, or when the engine is not heavily laden, while it opens up to ventilate the crankcase gases when the load on the engine is higher. Also, the function of the PCV Valve is as an anti-flame chamber and, at the same time, it is related to the increase of the engine power with the help of compression. This is why it is important to ensure that the PCV Valve is periodically checked, so that you do not have to deal with expensive car repairs, or a car that does not run as it should.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Wrangler PCV Valve at great affordable prices. Moreover, all genuine Jeep Wrangler PCV Valve come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Jeep Wrangler PCV Valve Parts Questions & Experts Answers
- Q:How to replace the PCV valve and PCV Hose on Jeep Wrangler?A:The PCV valve is found in the valve cover top in inline engines, left-side valve cover in 3.BLV6, and rear of the right-side valve cover in 3.6L V6. For inline and 3.8L V6 engines, remove the valve from its grommet and hose, noting its position. In the 3.8L engine, it's near the ignition coil pack. For 3.6L V6, loosen the hose clamp, remove screws, and pull the valve from the right valve cover. Inspect the rubber grommet or 0-ring for damage and replace if needed. Secure the valve and hose into position and tighten screws for 3.6L V6. Later Inline six-cylinder models use a CCV system with a rubber fitting connected to the intake manifold by a plastic hose. If there's no vacuum, clean the hose and fitting orifice, or replace if damaged. Securely install the fitting and hose in the valve cover.
Related Jeep Wrangler Parts
Jeep Wrangler Oil Filter
Jeep Wrangler Air Filter
Jeep Wrangler Alternator
Jeep Wrangler Oxygen Sensor
Jeep Wrangler Fuel Pump
Jeep Wrangler Water Pump
Jeep Wrangler Ignition Switch
Jeep Wrangler Catalytic Converter
Jeep Wrangler Cabin Air Filter
Jeep Wrangler Wiper Blade
Jeep Wrangler Drive Belt
Jeep Wrangler Timing Belt
Browse by Year
2025 PCV Valve 2024 PCV Valve 2023 PCV Valve 2022 PCV Valve 2021 PCV Valve 2020 PCV Valve 2019 PCV Valve 2018 PCV Valve 2017 PCV Valve 2016 PCV Valve 2015 PCV Valve 2014 PCV Valve 2013 PCV Valve 2012 PCV Valve 2011 PCV Valve 2010 PCV Valve 2009 PCV Valve 2008 PCV Valve 2007 PCV Valve 2006 PCV Valve 2005 PCV Valve 2004 PCV Valve 2003 PCV Valve 1990 PCV Valve 1989 PCV Valve 1988 PCV Valve 1987 PCV Valve