Make sure this part fits

Mopar 4778149 Cylinder Lock-Door Lock Cylinder

1993-2011 Mopar 4778149

Customer Questions & Expert Answers (2)
4778149 Mopar Cylinder Lock-Door Lock Cylinder Product Photo 1 of 1
  • Part Description
    Cap Door Lock Cylinder Bright
  • Manufacturer
    Mopar
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Specifications
  • Fitment
  • Q&A
  • Product Specifications

    BrandGenuine Mopar
    Manufacturer Part Number4778149
    Part DescriptionCap Door Lock Cylinder Bright
    Other NamesCap
    Item Dimensions1.2 x 1.2 x 0.3 inches
    Item Weight0.40 Pounds
    ConditionNew
    ManufacturerMopar
    SKU4778149
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1999-2004 Chrysler 300M6 Cyl 3.5LBase
    2009, 2007 Chrysler Aspen8 Cyl 4.7L, 8 Cyl 5.7LLimited 2WD, Limited 4WD, Limited HEV 4WD
    1993-2004 Chrysler Concorde6 Cyl 2.7L, 6 Cyl 3.2L, 6 Cyl 3.3L, 6 Cyl 3.5LBase, Limited, LX, LXi
    2000 Chrysler Grand Voyager6 Cyl 3.0L, 6 Cyl 3.3LBase, SE
    1999-2001, 1994-1997 Chrysler LHS6 Cyl 3.5LBase
    1994-1996 Chrysler New Yorker6 Cyl 3.5LBase
    2001-2002 Chrysler Prowler6 Cyl 3.5LBase
    2001-2005 Chrysler Sebring4 Cyl 2.4L, 6 Cyl 2.7LBase Sedan, Limited Sedan, LX Sedan, LXi Sedan, Touring Sedan, TSI Sedan
    2000-2006, 1997-1998 Chrysler Town & Country6 Cyl 3.3L, 6 Cyl 3.5L, 6 Cyl 3.8LBase, EL, EX, Limited AWD, Limited FWD, LX AWD, LX FWD, LXi AWD, LXi FWD, SX, Touring AWD, Touring FWD
    2000-2003 Chrysler Voyager4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L, 6 Cyl 3.8LBase, EC, LX, SE
    View More
  • Customer Questions & Expert Answers

    Q:
    Is this part guaranteed to fit my truck?
    A:
    You can Select Your Vehicle to check if 4778149 fits your vehicle.
    Posted and answered by Mopar Parts Specialist Reggie
    Q:
    How to replace the Door Handle, Door Latch Assembly, and Door Lock Cylinder on the Chrysler Town & Country? Posted by Devonzell M.
    A:
    To replace the front door latch, shut the window fully and then, pop off the front door trim panel, lift up the plastic water shield to get to the inner door hardware. If reinforced with power door locks, the wire connector has to be disconnected from the power door lock motor. Remove the clips which fasten the linkage to the door latch and then the linkages then the screws mounting the door latch to the door end frame then take out the latch. Removal is the exact opposite of installation though one is advised to use new screws if the latch has been removed. When completed with the installation of the door latch by using new screws, slide in the linkage into the latch and engage the clips and if their is electrical connector reconnect it. For the outside handle, the initial steps as with the inside handle to reach the inside of the door release mechanism, and disconnect switch connector in case your car came with Vehicle Theft Security System, and release the push in fasteners. Take out the handle to the outer panel by taking out the latch and lock linkages from the handle. In the outside handle for the lock cylinder you will need to pop of a clip then pull it out then you will need to install the new lock cylinder retaining clip and position the link arm before pushing the lock cylinder back in. For the sliding door latch/lock control, it is necessary to remove the trim panel of the sliding door, disconnect the external cable given in the figure, and also remove the foam insulation block given in the figure. Remove the inside latch handle and free the clip where the inside door handle bell crank link was previously fixed, also use bolts to take off the latch/lock control from the sliding door. For the outside handle of the sliding door, the procedure is almost similar to the internal handle to gain access to the handle. For the liftgate latch, the trim panel and watershield must be pulled off, the connection of the outside lock cylinder link and wire connector have to be disconnected and the screws of the latch have to be loosened. The outside handle for the liftgate includes; removal of the trim panel, followed by the electrical connectors and finally the removal of mounting screws. Last but not least, to take out the liftgate lock cylinder, press the clip to release latch link, if there was an electrical connector, then disconnect it, then turn counterclockwise the plastic nut on the lock cylinder and remove it. To uninstall all the components the process is the exact opposite of installation.
    You can Select Your Vehicle to see complete installation and repair tips.
    Answered by Mopar Parts Specialist Jay / Sep 27, 2025

Genuine Mopar Part 4778149, the Right Choice

To ensure reliability, purchase Mopar part # 4778149 Cylinder Lock-Door Lock Cylinder. It is sometimes referred to as Door Lock Cylinder. The OEM parts should be used when the Mopar owners want to maximize their driving experience. The high-tech factories that produce these parts utilize sophisticated technology specifically designed to meet stringent factory requirements. Additionally, they are thoroughly tested and can thus be used with reliability by Mopar owners. This part fits specific Chrysler 300M, Sebring, and Town & Country models. It fits Dodge Dakota, Ram 1500, Ram 2500. It also fits Jeep Grand Cherokee and Liberty. This also fits Ram Dakota.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as 4778149 Cylinder Lock-Door Lock Cylinder. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at attractive prices. Further, all parts come with a manufacturer's warranty. For detailed Jeep parts information, click here.
Shop MoparPartsGiant.com for dedicated service, prompt delivery, and low prices on genuine parts from real OE dealerships.