How do you remove and install the shift cable on Chrysler 200?

For replacement of a shift cable, shift the vehicle in to park then disconnect the negative battery cable from the remote ground terminal or battery. Release the shift cable from the shift lever by using a trim panel tool or flat bladed screwdriver and remove the bracket and pull the cable loose from its connection at the bracket. Pull the center console, and at the shifter assembly, give a pin and disconnect the shift cable housing at the clip as well as the cable at the bracket. Lift the car and put jackstands securely then, remove the grommet on the floor and pull the shift cable out of the hole. Loosen the cable gently from the retainers under the vehicle and then take it out. For installation the process is just the reverse of the above mentioned process to be followed where the grommet must be properly installed to make it a perfect fit and it must be lubricated in case required. For adjustment, the vehicle has to be parked in an open flat surface, the parking brake has to be engaged and the gear lever has to be shifted to the park mode before turning off the key. Tighten the shift cable adjustment lever bolt at the transaxle shift lever with the shift lever at the transaxle in the Park position, which engages the parking pawl. Further, turn the adjustment lever bolt to the stipulated torque setting, determine the smoothness of shifts, and guarantee the possibility of engine startup only in the Park/Neutral modes. Last, power the transaxle through all gear shift positions to test the shift control cable and adjust if required.

Genuine Chrysler 200 Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Shift Cables found

View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 5273214AE
$226.35 MSRP: $343.00
You Save: $116.65 (35%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 5273214AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Chrysler 200 | Limited Sedan, LX Sedan, S Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 3.6L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 5273214AG
$226.35 MSRP: $343.00
You Save: $116.65 (35%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control; Shift Control Cable
- Replaces: 5273214AE, 5273214AF, 5273214AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 200 | Limited Sedan, LX Convertible, LX Sedan, S Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 3.6L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 5273214AF
$226.35 MSRP: $343.00
You Save: $116.65 (35%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 5273214AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2013 Chrysler 200 | Limited Sedan, LX Convertible, LX Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 4721942AC
$97.88 MSRP: $145.00
You Save: $47.12 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 4721942AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chrysler 200 | Limited Sedan, LX Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 5106009AC
$221.26 MSRP: $350.00
You Save: $128.74 (37%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaces: 5106009AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2012 Chrysler 200 | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 4721942AD
$97.88 MSRP: $145.00
You Save: $47.12 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control; Shift Control Cable
- Replaces: 4721942AB, 4721942AC, 4721942AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 200 | Limited Sedan, LX Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 68105824AA
$154.54 MSRP: $231.00
You Save: $76.46 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 68105824AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012 Chrysler 200 | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 68037777AB
$154.54 MSRP: $231.00
You Save: $76.46 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable-Gearshift Control
- Replaced by: 68105824AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Chrysler 200 | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 68105779AB
Product Specifications
- Other Name: Cable-Gearshift Control; Shift Control Cable
- Replaces: 68105779AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2014 Chrysler 200 | Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, S Convertible, S Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 3.6L
View related parts
Chrysler 200 Transmission Gearshift Control Cable
Part Number: 68105824AB
Product Specifications
- Other Name: Cable-Gearshift Control; Shift Control Cable
- Replaces: 68105824AA, 68037777AB, 68037777AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 200 | Limited Sedan, LX Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L

Chrysler 200 Shift Cable

The Chrysler 200 Shift Cable translates the driver's hand movement at the console lever into a corresponding motion at the manual lever of the transmission, allowing the driver to confidently pick every automatic gear. Safeguarded in a sheath, this Shift Cable defends against kinking while finely enabling flex to correlate with federally mandated PRNDL Park, Reverse, Neutral, Drive, and Low settings. The earlier Chrysler 200 editions relied on mechanical rods that had bushings that could get loose, which caused a vague shift. The later cars had a sealed single Shift Cable that protects the pathway from all the road dirt and other debris to reduce play. Having the Shift Cable on a Chrysler 200 examined at regular intervals can catch stretching before breaking. Cables are one of the most moved components inside the car, hence possible stretching or breakage. However, a simple replacement returns the crisp feeling. The recent Chrysler 200 generation introduced electronic shift by wire, which replaces the physical Shift Cable with sensors and a motor. This allows the car designer a lot of freedom and creativity in designing a rotary or push button selector inside the cabin. Moreover, it also eliminates any wear and tear on the linkage.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler 200 Shift Cable at great affordable prices. Moreover, all genuine Chrysler 200 Shift Cable come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler 200 Shift Cable Parts Questions & Experts Answers

Transmission Gearshift Control Cable
5273214AF
Q: How do you remove and install the shift cable on Chrysler 200?
A:
For replacement of a shift cable, shift the vehicle in to park then disconnect the negative battery cable from the remote ground terminal or battery. Release the shift cable from the shift lever by using a trim panel tool or flat bladed screwdriver and remove the bracket and pull the cable loose from its connection at the bracket. Pull the center console, and at the shifter assembly, give a pin and disconnect the shift cable housing at the clip as well as the cable at the bracket. Lift the car and put jackstands securely then, remove the grommet on the floor and pull the shift cable out of the hole. Loosen the cable gently from the retainers under the vehicle and then take it out. For installation the process is just the reverse of the above mentioned process to be followed where the grommet must be properly installed to make it a perfect fit and it must be lubricated in case required. For adjustment, the vehicle has to be parked in an open flat surface, the parking brake has to be engaged and the gear lever has to be shifted to the park mode before turning off the key. Tighten the shift cable adjustment lever bolt at the transaxle shift lever with the shift lever at the transaxle in the Park position, which engages the parking pawl. Further, turn the adjustment lever bolt to the stipulated torque setting, determine the smoothness of shifts, and guarantee the possibility of engine startup only in the Park/Neutral modes. Last, power the transaxle through all gear shift positions to test the shift control cable and adjust if required.

Related Chrysler 200 Parts

Browse by Year

2014 Shift Cable 2013 Shift Cable 2012 Shift Cable 2011 Shift Cable