How to replace the turn signal and Hazard Warning Switch on Chrysler Imperial?

The turn signal switch is located at the top end of the steering column and is operated by the multi-function control stalk, with the hazard warning switch mounted underneath it, next to the ignition key light. To begin, disconnect the negative cable from the battery and remove the steering column lower cover. Unplug the turn signal switch electrical connector and use an ohmmeter or self-powered test light to check for continuity between the indicated switch connector terminals, replacing the turn signal or hazard switch if the continuity is not as specified. For replacement, disconnect the negative battery cable, then remove the steering wheel and detach the wiring harness trough from the steering column. Unplug the electrical connector and remove the wiper/washer switch pivot screw while leaving the control stalk in place. Remove the three screws to detach the turn signal switch, carefully pulling the wiring harness out through the top of the steering column. Installation is the reverse of removal, ensuring to lubricate the steering shaft contact surfaces with multi-purpose grease and to securely locate the dimmer switch rod in the pocket of the control stalk.

Genuine Chrysler Imperial Hazard Warning Switch

Hazard Warning Emergency Light Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Hazard Warning Switches found

View related parts
Chrysler Imperial
Part Number: 4326603
Product Specifications
- Other Name: Hazard Switch, Turn Signal Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1993 Chrysler Imperial | Base | 6 Cyl 3.0L, 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Imperial Switch-Multi Function
Part Number: 4638063
Product Specifications
- Other Name: Switch, Turn Signal & Hazard Warning; Front Wiper Switch, Switch, Turn Signal Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chrysler Imperial | Base | 6 Cyl 3.0L, 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Imperial Switch
Part Number: 4373412
Product Specifications
- Other Name: Turn Signal & Hazard Warning, w/o Tilt
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Imperial | 6 Cyl 3.3L

Chrysler Imperial Hazard Warning Switch

Chrysler Imperial Hazard Warning Switch is a system that will turn on all four turn signal lamps simultaneously in order to warn other traffic or at the roadside stop of a hazard. Hazard Warning Switch is mounted as a dashboard button, which is pressed to activate emergency flashers that turn off normal turn signal operation. The Hazard Warning Switch system actually lights up each corner when activated to provide a blinking light signal in unison, to create an attention-grabbing warning signal that is visible several yards away. The Hazard Warning Switch is pressed a second time and the sequence is terminated, as normal signaling is resumed. The Hazard Warning Switch is an elementary electrical system and it is a good safety alert in all Chrysler vehicles with the Imperial name in the car and it is one sure way of Chrysler drivers who drive an Imperial to communicate an emergency situation.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Imperial Hazard Warning Switch at great affordable prices. Moreover, all genuine Chrysler Imperial Hazard Warning Switch come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Imperial Hazard Warning Switch Parts Questions & Experts Answers

4326603
Q: How to replace the turn signal and Hazard Warning Switch on Chrysler Imperial?
A:
The turn signal switch is located at the top end of the steering column and is operated by the multi-function control stalk, with the hazard warning switch mounted underneath it, next to the ignition key light. To begin, disconnect the negative cable from the battery and remove the steering column lower cover. Unplug the turn signal switch electrical connector and use an ohmmeter or self-powered test light to check for continuity between the indicated switch connector terminals, replacing the turn signal or hazard switch if the continuity is not as specified. For replacement, disconnect the negative battery cable, then remove the steering wheel and detach the wiring harness trough from the steering column. Unplug the electrical connector and remove the wiper/washer switch pivot screw while leaving the control stalk in place. Remove the three screws to detach the turn signal switch, carefully pulling the wiring harness out through the top of the steering column. Installation is the reverse of removal, ensuring to lubricate the steering shaft contact surfaces with multi-purpose grease and to securely locate the dimmer switch rod in the pocket of the control stalk.