How to remove a Rack and Pinion steering gear on Chrysler Sebring?

Pull your car up and set the wheels right in front of you. Unplug the negative battery cable either from the battery terminal or at the remote ground terminal. Drain as much steering fluid as you can from the power pump. Slowly turn the wheel nuts, lift your vehicle with the jack, put draft stops under its body, and take off your wheels. After aligning the steering wheel to the right, take out the one bolt that holds the middle shaft. Mount the steering wheel in its original position and ensure it is safe to drive, then disconnect the section connecting the steering input to the gear mechanism. Loosen and take off both connection parts that join the steering knuckles to the tie rods. Take out the bolt holding the rear engine mount. Remove the longitudinal crossmember. Loosen and remove the brackets that attach the power steering hose on the crossmember. Loosen tube nut on the return line connected to the Rack And Pinion and take it off. Simplest way to detach the Rack And Pinion door is to loosen the tube nut connected to the pressure line. Drop the screws that keep the Rack And Pinion heat shield in place and take off the shield. Remove the subframe. First remove the firewall seals, then take out the bolts joining the Rack And Pinion to the subframe before removing the Rack And Pinion itself. Installation is the reverse of removal, taking note of the following points: When installing a fresh Rack And Pinion, set it straight first by turning the input shaft clockwise until it can move no further. Then turn the same input shaft counterclockwise until it rests, then count how long it took to stop. Turn your input shaft right 2/3 of the counts that you noted earlier. Install the mounting bolts and tighten them. Put the indexes from the steering shaft and coupler together before placing the bolt in the coupler. Screw the fluid hoses into their right places on the Rack And Pinion and lock them with firm turns. Fasten the engine mount bolt and tighten the crossmember bolts and reinforcement structures. Install the wheels and lug nuts. Lower the vehicle, then tighten the lug nuts. Add the right steering fluid to the power steering pump reservoir, then let all excess air escape from the steering system. Check your front wheel alignment and fix it if there are any issues.

Genuine Chrysler Sebring Rack And Pinion

Steering Rack And Pinion

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

54 Rack And Pinions found

View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 4743879AG
$343.12 MSRP: $530.00
You Save: $186.88 (36%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 4743879AL
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Sebring | Limited Convertible, LX Convertible, Touring Convertible | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 68093008AB
$414.26 MSRP: $604.00
You Save: $189.74 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 68093008AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Sebring | Limited Convertible, LX Convertible, Touring Convertible | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 5272822AF
$524.08 MSRP: $1195.00
You Save: $670.92 (57%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 68093002AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chrysler Sebring | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 5272822AE
$524.08 MSRP: $1195.00
You Save: $670.92 (57%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 68093002AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chrysler Sebring | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 4743875AF
$350.42 MSRP: $510.00
You Save: $159.58 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 4743875AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Sebring | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 5093808AA
$218.15 MSRP: $320.00
You Save: $101.85 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 4764995AF
$355.68 MSRP: $520.00
You Save: $164.32 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 4743875AE
$350.42 MSRP: $510.00
You Save: $159.58 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 4743875AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Sebring | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 4743878AG
$414.26 MSRP: $604.00
You Save: $189.74 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 68093008AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Sebring | Limited Convertible, LX Convertible, Touring Convertible | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 5093818AA
$423.38 MSRP: $617.00
You Save: $193.62 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 4764403AE
$210.94 MSRP: $312.00
You Save: $101.06 (33%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan | 6 Cyl 2.7L
View related parts
Chrysler Sebring Rack And Pinion Complete Unit
Part Number: MR589197
$141.78 MSRP: $180.42
You Save: $38.64 (22%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chrysler Sebring | Base, LX | 4 Cyl 2.4L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 5093819AA
$303.88 MSRP: $447.00
You Save: $143.12 (33%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan | 6 Cyl 2.7L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 5093817AA
$223.79 MSRP: $329.00
You Save: $105.21 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly, Steering Gear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan | 6 Cyl 2.7L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 5093816AA
$354.98 MSRP: $517.00
You Save: $162.02 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2004 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan, Touring Convertible, Touring Sedan | 6 Cyl 2.7L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 5272823AF
$377.78 MSRP: $550.00
You Save: $172.22 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 68093007AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chrysler Sebring | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 5272823AE
$377.78 MSRP: $550.00
You Save: $172.22 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 68093007AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chrysler Sebring | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 5272823AD
$377.78 MSRP: $550.00
You Save: $172.22 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Power Steering ; Gear Rack And Pinion
- Replaced by: 68093007AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Sebring | Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Rack And Pinion Gear
Part Number: 4743878AF
$414.26 MSRP: $604.00
You Save: $189.74 (32%)
ADD TO CART
Product Specifications
- Other Name: Gear-Rack And Pinion
- Replaced by: 68093008AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Sebring | Limited Convertible, LX Convertible, Touring Convertible | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler Sebring Power Steering Gear
Part Number: 4764920AD
$236.88 MSRP: $350.00
You Save: $113.12 (33%)
Product Specifications
- Other Name: Gear-Power Steering; Gear Assembly
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan | 6 Cyl 2.7L

| Page 1 of 3 |Next >

1-20 of 54 Results

Chrysler Sebring Rack And Pinion

The Rack And Pinion is another fairly important part of the car, or more particularly the Chrysler Sebring vehicles, as it adapts the rotational motion of the steering wheel into lateral motion of the front wheels. It is a rack and pinion type where there is a pinion gear connected to the steering column and the rack gear is provided within a metallic pipe and when the steering wheel in turned the wheels are moved. The Chrysler Sebring models mainly use power-Rack And Pinions and pinion devices, which make the turning easier by using hydraulic fluid. Manual racks are traditional while hydraulic systems are used in today's Sebring vehicles, these hydraulic systems can sometimes develop problems as a result of leakage or worn out gears, thus the possible replacement of the Rack And Pinion. Other design modifications, for example, in racks, can also affect performance, straight racks are normally used in preference to helical types because the latter tend to operate at higher temperatures.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Sebring Rack And Pinion at great affordable prices. Moreover, all genuine Chrysler Sebring Rack And Pinion come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Sebring Rack And Pinion Parts Questions & Experts Answers

Rack And Pinion Gear
4743875AE
Q: How to remove a Rack and Pinion steering gear on Chrysler Sebring?
A:
Pull your car up and set the wheels right in front of you. Unplug the negative battery cable either from the battery terminal or at the remote ground terminal. Drain as much steering fluid as you can from the power pump. Slowly turn the wheel nuts, lift your vehicle with the jack, put draft stops under its body, and take off your wheels. After aligning the steering wheel to the right, take out the one bolt that holds the middle shaft. Mount the steering wheel in its original position and ensure it is safe to drive, then disconnect the section connecting the steering input to the gear mechanism. Loosen and take off both connection parts that join the steering knuckles to the tie rods. Take out the bolt holding the rear engine mount. Remove the longitudinal crossmember. Loosen and remove the brackets that attach the power steering hose on the crossmember. Loosen tube nut on the return line connected to the Rack And Pinion and take it off. Simplest way to detach the Rack And Pinion door is to loosen the tube nut connected to the pressure line. Drop the screws that keep the Rack And Pinion heat shield in place and take off the shield. Remove the subframe. First remove the firewall seals, then take out the bolts joining the Rack And Pinion to the subframe before removing the Rack And Pinion itself. Installation is the reverse of removal, taking note of the following points: When installing a fresh Rack And Pinion, set it straight first by turning the input shaft clockwise until it can move no further. Then turn the same input shaft counterclockwise until it rests, then count how long it took to stop. Turn your input shaft right 2/3 of the counts that you noted earlier. Install the mounting bolts and tighten them. Put the indexes from the steering shaft and coupler together before placing the bolt in the coupler. Screw the fluid hoses into their right places on the Rack And Pinion and lock them with firm turns. Fasten the engine mount bolt and tighten the crossmember bolts and reinforcement structures. Install the wheels and lug nuts. Lower the vehicle, then tighten the lug nuts. Add the right steering fluid to the Power Steering Pump reservoir, then let all excess air escape from the steering system. Check your front wheel alignment and fix it if there are any issues.