How to Replace the Cooling Fan on My Dodge Avenger?

If the engine is overheating and the cooling fan is not coming on when the engine temperature rises to an excessive level, check the fan relays in the underhood fuse/relay box. If the relays are okay, check all wiring and connections to the fan motor. If no obvious problems are found, the problem could be the Engine Coolant Temperature (ECT) sensor or the Powertrain Control Module (PCM). Have the cooling fan system and circuit diagnosed by a dealer service department or repair shop with the proper diagnostic equipment. To replace the cooling fan, start by disconnecting the negative battery cable. Set the parking brake, raise the front of the vehicle and support it securely on jackstands. Drain the cooling system. Disconnect the cooling fan electrical connector and harness retaining pins. On 2011 and later models, remove the fasteners holding the wire loom to the upper radiator core support. Remove the upper radiator hose from the radiator. On 2011 and later models, remove the oil dipstick tube to make room for fan removal. Remove the upper clips and fasteners holding the fan assembly to the radiator. On later models, remove the fan shroud mounting bolts. Remove the cooling fan assembly by pulling it straight up and out of the engine compartment. Installation is the reverse of removal. Place the fan assembly back into the retaining clips for the side and bottom. Refill the cooling system.

Genuine Dodge Avenger Engine Cooling Fan

Radiator Fan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Engine Cooling Fans found

View related parts
Dodge Avenger Cooling Fan
Part Number: 68031871AA
$191.25 MSRP: $284.00
You Save: $92.75 (33%)
ADD TO CART
Product Specifications
- Other Name: Fan Cooling; Fan Assembly, Fan Blade
- Replaces: 5104787AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2014 Dodge Avenger | Express, Heat, LUX, Mainstreet, R/T AWD, R/T FWD, SE, SXT, SXT Plus | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L, 6 Cyl 3.6L
View related parts
Dodge Avenger Fan Condenser
Part Number: MR206990
Product Specifications
- Other Name: Blade
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 4 Cyl 2.0L, 6 Cyl 2.5L
View related parts
Dodge Avenger Fan Cooling
Part Number: MB906062
Product Specifications
- Other Name: Blade, Fan Blade
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1999 Dodge Avenger | Base, ES | 4 Cyl 2.0L, 6 Cyl 2.5L
View related parts
Dodge Avenger Radiator Cooling Fan Module
Part Number: 68004051AA
Product Specifications
- Other Name: Fan Module Radiator Cooling; Fan Assembly, Fan Module, Fan Motor Assembly
- Replaces: 5191253AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Avenger | R/T AWD, R/T FWD, SE, SXT | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Dodge Avenger Radiator Cooling Fan Module
Part Number: 68002661AA
Product Specifications
- Other Name: Fan Module Radiator Cooling; Fan Assembly, Fan Module, Fan Motor Assembly
- Replaces: 5191289AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Avenger

Dodge Avenger Engine Cooling Fan

The Dodge Avenger Engine Cooling Fan keeps the sedan's powerplant from overheating by pulling air through the radiator whenever natural airflow falls short, especially at idle or in traffic. Mounted just behind the grille, the Engine Cooling Fan sits in an assembly with motor, shroud, and multi-bladed wheel that channels a steady breeze across radiator fins so hot coolant sheds heat before returning to the engine, and this Dodge part prevents power loss. Earlier Avenger models applied a belt-driven mechanical setup that spun with engine speed, while later Dodge Avenger generations adopted an electric Engine Cooling Fan governed by temperature sensors for instant response and better fuel economy. Some versions of the model also came with a dual Engine Cooling Fan package that boosts airflow for high-output engines. The electric style delivers maximum cooling even when the car is stationary, whereas the mechanical unit depended on higher rpm to move similar air. Whichever design is fitted, every Dodge Avenger relies on its Engine Cooling Fan to stabilize temperature, protect performance, and extend engine life.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Avenger Engine Cooling Fan at great affordable prices. Moreover, all genuine Dodge Avenger Engine Cooling Fan come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Avenger Engine Cooling Fan Parts Questions & Experts Answers

Cooling Fan
68031871AA
Q: How to Replace the Cooling Fan on My Dodge Avenger?
A:
If the engine is overheating and the cooling fan is not coming on when the engine temperature rises to an excessive level, check the fan relays in the underhood fuse/relay box. If the relays are okay, check all wiring and connections to the fan motor. If no obvious problems are found, the problem could be the Engine Coolant Temperature (ECT) sensor or the Powertrain Control Module (PCM). Have the cooling fan system and circuit diagnosed by a dealer service department or repair shop with the proper diagnostic equipment. To replace the cooling fan, start by disconnecting the negative battery cable. Set the parking brake, raise the front of the vehicle and support it securely on jackstands. Drain the cooling system. Disconnect the cooling fan electrical connector and harness retaining pins. On 2011 and later models, remove the fasteners holding the wire loom to the upper radiator core support. Remove the upper radiator hose from the radiator. On 2011 and later models, remove the oil dipstick tube to make room for fan removal. Remove the upper clips and fasteners holding the fan assembly to the radiator. On later models, remove the fan shroud mounting bolts. Remove the cooling fan assembly by pulling it straight up and out of the engine compartment. Installation is the reverse of removal. Place the fan assembly back into the retaining clips for the side and bottom. Refill the cooling system.