How to remove and install the Washer Pump, Washer Reservoir, and Wiper Motor on the Dodge Challenger?

Disconnect the cable from the negative battery terminal as the first step of replacing the windshield wiper motor in Chrysler 300, Dodge Charger, and Dodge Challenger. Take away the rubber shields over each wiper arm and unscrew the nuts that hold the arms in position, but write down where they go before you lift them off. Squeeze the release tab on the windshield wiper motor connector, pull it out from its electrical plug, and move on. Take off the housing hardware that secures the windshield wiper module then disconnect it. Separate the link rods from the bellcrank using a special trim tool or large screwdriver. Then unscrew the bellcrank nut from its mounting position on the wiper motor shaft. Use a small puller to free the bellcrank from the wiper motor's shaft. Take out the wiper motor from its mounting place after removing bolts. Check for damage to the plastic motor insulator as you do this. First, find the washer bottle just in front of the right front tire, detach the battery negative cable, and remove the fasteners from the front part of the right engine cover. Put a catch pan under the fluid reservoir before you take out the pump or level sensor, then remove the electrical plugs from these parts. Detach the washer pump's hoses, easily pull out the old pump, and push in the new pump to its correct place in the reservoir. Lift up the right inner fender splash shield and unscrew the mounting bolts. Pull the reservoir through the space in the fenderwell, and reverse these steps for installation.

Genuine Dodge Challenger Washer Reservoir

Windshield Washer Reservoir

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Washer Reservoirs found

View related parts
Dodge Challenger Windshield Washer Reservoir
Part Number: 68125524AA
$110.19 MSRP: $165.00
You Save: $54.81 (34%)
ADD TO CART
Product Specifications
- Other Name: Reservoir Windshield Washer; Reservoir, Washer Reservoir
- Replaces: 68125524AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Challenger | GT AWD, GT RWD, R/T, R/T 392 RWD, R/T RWD, R/T Scat Pack, R/T Scat Pack RWD, SE, SRT, SRT 392, SRT 392 RWD, SRT Core, SRT Demon RWD, SRT Hellcat, SRT Hellcat RWD, SRT8, SRT8 Core, SXT, SXT AWD, SXT Plus, SXT RWD | 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.2L, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Challenger Windshield Washer Reservoir
Part Number: 5170706AA
$41.94 MSRP: $60.55
You Save: $18.61 (31%)
ADD TO CART
Product Specifications
- Other Name: Reservoir Windshield Washer; Reservoir, Washer Reservoir
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Challenger | R/T, SE, SRT8 | 6 Cyl 3.5L, 8 Cyl 5.7L, 8 Cyl 6.1L
View related parts
Dodge Challenger Windshield Washer Reservoir
Part Number: 68125524AB
$110.19 MSRP: $165.00
You Save: $54.81 (34%)
ADD TO CART
Product Specifications
- Other Name: Reservoir Windshield Washer
- Replaced by: 68125524AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013 Dodge Challenger | R/T, SE, SRT8, SRT8 Core | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Dodge Challenger Windshield Washer Reservoir
Part Number: 68617758AA
$69.20 MSRP: $103.00
You Save: $33.80 (33%)
Product Specifications
- Other Name: RESERVOIR-WINDSHIELD WASHER; Washer Reservoir
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS

Dodge Challenger Washer Reservoir

The Windshield Washer Reservoir is an important component which is used to contain windshield washer fluid in the Dodge Challenger cars for better sight for drivers. Usually made of hard plastic, the reservoir's location in the engine compartment also differs, as some models put it behind the engine, while others place it near the headlight. Subsequently, it is probable that Dodge Challenger models have employed different styles of the Windshield Washer Reservoir throughout the years, while particular differences are not identified. In all of them the factor remains the toughness of the part itself, as it plastic over time Yellow and becomes brittle and cracks if it is not filled with washer fluid sufficiently. This brings out the need of performing service check up on the Windshield Washer Reservoir in order to enhance its proficiency in Dodge Challenger cars.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Challenger Washer Reservoir at great affordable prices. Moreover, all genuine Dodge Challenger Washer Reservoir come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Challenger Washer Reservoir Parts Questions & Experts Answers

Windshield Washer Reservoir
68125524AA
Q: How to remove and install the Washer Pump, Washer Reservoir, and Wiper Motor on the Dodge Challenger?
A:
Disconnect the cable from the negative battery terminal as the first step of replacing the windshield wiper motor in Chrysler 300, Dodge Charger, and Dodge Challenger. Take away the rubber shields over each wiper arm and unscrew the nuts that hold the arms in position, but write down where they go before you lift them off. Squeeze the release tab on the windshield wiper motor connector, pull it out from its electrical plug, and move on. Take off the housing hardware that secures the windshield wiper module then disconnect it. Separate the link rods from the bellcrank using a special trim tool or large screwdriver. Then unscrew the bellcrank nut from its mounting position on the wiper motor shaft. Use a small puller to free the bellcrank from the wiper motor's shaft. Take out the wiper motor from its mounting place after removing bolts. Check for damage to the plastic motor insulator as you do this. First, find the washer bottle just in front of the right front tire, detach the battery negative cable, and remove the fasteners from the front part of the right engine cover. Put a catch pan under the fluid reservoir before you take out the pump or level sensor, then remove the electrical plugs from these parts. Detach the washer pump's hoses, easily pull out the old pump, and push in the new pump to its correct place in the reservoir. Lift up the right inner fender splash shield and unscrew the mounting bolts. Pull the reservoir through the space in the fenderwell, and reverse these steps for installation.