How to remove and install the blower motor and blower motor resistor on Dodge Durango?

When replacing the automatic temperature control module in Durango models you must install the power module instead of using a blower motor resistor by following the same mounting and replacing procedures. First detach the black wire connected to the negative side of the battery. Uninstall the blower motor resistor after removing its mounting screws and disconnecting electrical connectors and cover then reinstall it in reverse order. The blower motor replacement process starts with removing the kick panel on the front right side of the vehicle followed by disconnecting the electrical connector before unscrewing mounting screws which lower the motor from its housing. When the motor shows signs of damage it must be replaced with a new unit. The rear replacement steps begin with disconnecting the negative terminal and removing the right rear interior quarter panel and disconnecting the blower motor resistor connector followed by removing its mounting screw. The process to replace the rear blower motor necessitates professional discharge of air conditioning system refrigerant followed by disconnecting the refrigerant line fitting and pinching off heater hoses before right rear interior quarter panel and air ducts removal. Start by disconnecting the housing electrical connectors followed by removing screws that hold mounting fasteners before lifting the housing free. Following the removal of the blower motor connector disconnect its mounting screws and remove the blower motor from its position. The installation process requires reversing these steps while installing new O-rings that are specifically designed for R-134a refrigerant and using appropriate oil. The system should be evacuated then recharged and leak-tested before checking the coolant level.

Genuine Dodge Durango Blower Motor

A/C Heater Blower Motor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Blower Motors found

View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 68224166AB
$220.50 MSRP: $331.00
You Save: $110.50 (34%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel; Blower Motor
- Replaces: 68224166AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2025 Dodge Durango | Citadel AWD, Citadel RWD, GT AWD, GT RWD, Limited AWD, Limited RWD, Pursuit Vehicle AWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD, SRT 392 AWD, SRT AWD, SRT Hellcat AWD, SXT AWD, SXT RWD | 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.2L, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 68224166AA
$220.50 MSRP: $331.00
You Save: $110.50 (34%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel
- Replaced by: 68224166AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2015 Dodge Durango | Citadel AWD, Citadel RWD, Limited AWD, Limited RWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD, SXT AWD, SXT RWD | 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 68089094AA
$186.21 MSRP: $384.00
You Save: $197.79 (52%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel; Blower Motor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2025 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Express AWD, Express RWD, GT AWD, GT RWD, Heat AWD, Heat RWD, Limited AWD, Limited RWD, Pursuit Vehicle AWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD, SRT 392 AWD, SRT AWD, SXT AWD, SXT RWD | 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 68079477AB
$190.13 MSRP: $284.00
You Save: $93.87 (34%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel; Blower Motor
- Replaces: 68079477AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Express AWD, Express RWD, Heat AWD, Heat RWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD, SXT AWD, SXT RWD | 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 68079477AA
$190.13 MSRP: $284.00
You Save: $93.87 (34%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel
- Replaced by: 68079477AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Express AWD, Express RWD, Heat AWD, Heat RWD, R/T AWD, R/T RWD | 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 5061381AA
$204.75 MSRP: $308.00
You Save: $103.25 (34%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel With Wheel and Cap; Blower Motor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2009 Dodge Durango | Adventurer 2WD, Adventurer 4WD, Limited 2WD, Limited 4WD, Limited HEV 4WD, SE 2WD, SE 4WD, SLT 2WD, SLT 4WD, ST 2WD, ST 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 5019640AB
$148.03 MSRP: $197.00
You Save: $48.97 (25%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel; Blower Motor
- Replaces: 5019640AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2008 Dodge Durango | Adventurer 2WD, Adventurer 4WD, Base 2WD, Base 4WD, Limited 2WD, Limited 4WD, R/T 4WD, SLT 2WD, SLT 4WD, SLT Plus 2WD, SLT Plus 4WD, Sport 2WD, Sport 4WD, ST 2WD, ST 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 5.9L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 5019640AA
$131.98 MSRP: $197.00
You Save: $65.02 (34%)
ADD TO CART
Product Specifications
- Other Name: Motor Blower with Wheel
- Replaced by: 5019640AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Dodge Durango | Base 2WD, Base 4WD, Limited 2WD, Limited 4WD, R/T 4WD, SLT 2WD, SLT 4WD, SLT Plus 2WD, SLT Plus 4WD, Sport 2WD, Sport 4WD, ST 2WD, ST 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 5.9L
View related parts
Dodge Durango Motor, A/C. Blower (Use Insul. 4419526)
Part Number: R5264068
Product Specifications
- Replaced by: 5015865AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Dodge Durango | Base 2WD, Base 4WD | 6 Cyl 3.9L, 8 Cyl 4.7L, 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Durango Motor Heater Blower
Part Number: 5264068
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Dodge Durango | Base 2WD, Base 4WD | 6 Cyl 3.9L, 8 Cyl 4.7L, 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Durango Blower Motor
Part Number: 5061382AA
Product Specifications
- Other Name: Motor Blower
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Durango | Limited 2WD, Limited 4WD, SLT 2WD, SLT 4WD, ST 2WD, ST 4WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 5003134AA
Product Specifications
- Other Name: Motor Blower with Wheel; Blower Motor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Dodge Durango | Base 2WD, Base 4WD | 6 Cyl 3.9L, 8 Cyl 4.7L, 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 4885669AD
Product Specifications
- Other Name: Motor Blower with Wheel
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Dodge Durango | R/T 4WD, SLT 2WD, SLT 4WD, SLT Plus 2WD, SLT Plus 4WD, Sport 2WD, Sport 4WD | 8 Cyl 4.7L, 8 Cyl 5.9L
View related parts
Dodge Durango Motor-Blower W/WHEEL
Part Number: 4885669AB
Product Specifications
- Other Name: Motor Blower with Wheel
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002 Dodge Durango | R/T 4WD, SLT 2WD, SLT 4WD, SLT Plus 2WD, SLT Plus 4WD, Sport 2WD, Sport 4WD | 8 Cyl 4.7L, 8 Cyl 5.9L
View related parts
Dodge Durango Motor-Blower With Wheel
Part Number: 68046013AA
Product Specifications
- Other Name: Motor Blower with Wheel; Blower Motor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Durango | Adventurer 2WD, Adventurer 4WD, Limited 2WD, Limited 4WD, Limited HEV 4WD, SE 2WD, SE 4WD, SLT 2WD, SLT 4WD, SXT 2WD, SXT 4WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L

Dodge Durango Blower Motor

Blower Motor of Dodge Durango vehicles is an indispensable component of the automobile's heating and cooling system, which helps circulate air in the vehicle. Some of the operations it performs includes regulation of air conditioning and assisting in suppression of engine overheating. A working blower motor is crucial for a comfortable ride to be delivered while a faulty one may enable the car to run yet the comfort won't be as desired. Depending on the models of Dodge Durango, there might be changes in terms of blower motoring, some cars might have only one blower motor while others might have two - one at the heater box and another at the rear place. This variation will enable greater control of the climate within the various parts of the car, thus meeting the needs of the passengers.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Durango Blower Motor at great affordable prices. Moreover, all genuine Dodge Durango Blower Motor come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Durango Blower Motor Parts Questions & Experts Answers

Motor-Blower With Wheel
5061381AA
Q: How to remove and install the blower motor and blower motor resistor on Dodge Durango?
A:
When replacing the automatic temperature control module in Durango models you must install the power module instead of using a blower motor resistor by following the same mounting and replacing procedures. First detach the black wire connected to the negative side of the battery. Uninstall the blower motor resistor after removing its mounting screws and disconnecting electrical connectors and cover then reinstall it in reverse order. The blower motor replacement process starts with removing the kick panel on the front right side of the vehicle followed by disconnecting the electrical connector before unscrewing mounting screws which lower the motor from its housing. When the motor shows signs of damage it must be replaced with a new unit. The rear replacement steps begin with disconnecting the negative terminal and removing the right rear interior quarter panel and disconnecting the blower motor resistor connector followed by removing its mounting screw. The process to replace the rear blower motor necessitates professional discharge of air conditioning system refrigerant followed by disconnecting the refrigerant line fitting and pinching off heater hoses before right rear interior quarter panel and air ducts removal. Start by disconnecting the housing electrical connectors followed by removing screws that hold mounting fasteners before lifting the housing free. Following the removal of the blower motor connector disconnect its mounting screws and remove the blower motor from its position. The installation process requires reversing these steps while installing new O-rings that are specifically designed for R-134a refrigerant and using appropriate oil. The system should be evacuated then recharged and leak-tested before checking the coolant level.