How to remove Pressure Plate,Release Bearing and Clutch Fork on Dodge Ram 3500?

To remove the clutch components, begin by raising and securely supporting the vehicle on jack stands. Disconnect the clutch release cylinder from the clutch housing without disconnecting the hydraulic fluid line. Proceed to remove the transmission, leaving the clutch fork and release bearing attached to the clutch housing. To support the clutch disc during removal, insert a clutch alignment tool through the clutch disc hub. Inspect the flywheel and pressure plate for indexing marks; if absent, create your own to ensure proper alignment during installation. Gradually loosen the pressure plate-to-flywheel bolts in a criss-cross pattern and remove them along with the pressure plate and clutch disc. Inspect all components, including the flywheel for defects, clutch disc for wear or damage, release bearing for replacement, and pressure plate for wear or damage. Clean the surfaces thoroughly and reinstall the flywheel. Align the clutch disc and pressure plate with an alignment tool and finger-tighten the pressure plate-to-flywheel bolts. Center the clutch disc using the alignment tool, then gradually tighten the bolts in a criss-cross pattern to the specified torque. Remove the alignment tool, lubricate the release bearing and related parts with high-temperature grease, reinstall the clutch release bearing if removed, and proceed to reinstall the transmission and all previously removed components. Finally, lower the vehicle.

Genuine Dodge Ram 3500 Release Bearing

Clutch Release Throw Out Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Release Bearings found

View related parts
Dodge Ram 3500 Clutch Release Bearing
Part Number: 52087514
$169.88 MSRP: $257.00
You Save: $87.12 (34%)
ADD TO CART
Product Specifications
- Other Name: Bearing Clutch Release; Release Bearing
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-2010 Dodge Ram 3500 | 3-Person Cab 2WD, 3-Person Cab 4WD, Club Cab 2WD, Club Cab 4WD, Club Cab 8FT BOX 2WD, Club Cab 8FT BOX 4WD, Laramie Crew Cab 2WD, Laramie Crew Cab 4WD, Laramie Mega Cab 2WD, Laramie Mega Cab 4WD, Laramie Quad Cab 2WD, Laramie Quad Cab 4WD, Laramie Regular Cab 2WD, Laramie Regular Cab 4WD, Mega Cab 2WD, Mega Cab 4WD, Quad Cab 2WD, Quad Cab 4WD, Quad Cab Chassis 2WD, Quad Cab Chassis 4WD, Quad Chassis CAB 2WD, Quad Chassis CAB 4WD, Regular Cab 2WD, Regular Cab 4WD, Regular Cab 8FT BOX 2WD, Regular Cab 8FT BOX 4WD, Regular Cab Chassis 2WD, Regular Cab Chassis 4WD, Regular Chassis CAB 2WD, Regular Chassis CAB 4WD, SLT Crew Cab 2WD, SLT Crew Cab 4WD, SLT Mega Cab 2WD, SLT Mega Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, ST Crew Cab 2WD, ST Crew Cab 4WD, ST Quad Cab 2WD, ST Quad Cab 4WD, ST Regular Cab 2WD, ST Regular Cab 4WD | 10 Cyl 8.0L, 6 Cyl 5.9L Diesel, 6 Cyl 6.7L Diesel, 8 Cyl 5.9L
View related parts
Dodge Ram 3500 Clutch Release Bearing
Part Number: 53008342
$154.13 MSRP: $231.00
You Save: $76.87 (34%)
ADD TO CART
Product Specifications
- Other Name: Bearing Clutch Release; Release Bearing
- Replaces: 53008342AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-2008 Dodge Ram 3500 | 3-Person Cab 2WD, 3-Person Cab 4WD, Club Cab 2WD, Club Cab 4WD, Club Cab 8FT BOX 2WD, Club Cab 8FT BOX 4WD, Laramie Mega Cab 2WD, Laramie Mega Cab 4WD, Laramie Quad Cab 2WD, Laramie Quad Cab 4WD, Laramie Regular Cab 2WD, Laramie Regular Cab 4WD, Quad Cab 2WD, Quad Cab 4WD, Quad Cab Chassis 2WD, Quad Cab Chassis 4WD, Regular Cab 2WD, Regular Cab 4WD, Regular Cab 8FT BOX 2WD, Regular Cab 8FT BOX 4WD, Regular Cab Chassis 2WD, Regular Cab Chassis 4WD, SLT Mega Cab 2WD, SLT Mega Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, ST Quad Cab 2WD, ST Quad Cab 4WD, ST Regular Cab 2WD, ST Regular Cab 4WD | 10 Cyl 8.0L, 6 Cyl 5.9L Diesel, 8 Cyl 5.7L, 8 Cyl 5.9L
View related parts
Dodge Ram 3500 Clutch Release Bearing
Part Number: 53008342AB
$154.13 MSRP: $231.00
You Save: $76.87 (34%)
ADD TO CART
Product Specifications
- Other Name: Bearing Clutch Release
- Replaced by: 53008342
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Dodge Ram 3500 | SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, ST Quad Cab 2WD, ST Quad Cab 4WD, ST Regular Cab 2WD, ST Regular Cab 4WD | 8 Cyl 5.7L
View related parts
Dodge Ram 3500 Bearing-OVERRUNNING Clutch
Part Number: 4461124
Product Specifications
- Other Name: Race Overrunning Clutch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-2009 Dodge Ram 3500 | 3-Person Cab 2WD, 3-Person Cab 4WD, Club Cab 2WD, Club Cab 4WD, Club Cab 8FT BOX 2WD, Club Cab 8FT BOX 4WD, Laramie Mega Cab 2WD, Laramie Mega Cab 4WD, Laramie Quad Cab 2WD, Laramie Quad Cab 4WD, Laramie Regular Cab 2WD, Laramie Regular Cab 4WD, Mega Cab 2WD, Mega Cab 4WD, Quad Cab 2WD, Quad Cab 4WD, Regular Cab 2WD, Regular Cab 4WD, Regular Cab 8FT BOX 2WD, Regular Cab 8FT BOX 4WD, Regular Cab Chassis 2WD, Regular Cab Chassis 4WD, SLT Mega Cab 2WD, SLT Mega Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, ST Quad Cab 2WD, ST Quad Cab 4WD, ST Regular Cab 2WD, ST Regular Cab 4WD | 10 Cyl 8.0L, 6 Cyl 5.9L Diesel, 6 Cyl 6.7L Diesel, 8 Cyl 5.9L

Dodge Ram 3500 Release Bearing

Dodge Ram 3500 Release Bearing allows the driver to interrupt engine torque fast so that gear shifts remain smooth and the heavy truck does not damage its transmission. This little bearing sits on the clutch housing. When the clutch pedal presses down, it moves along a hollow shaft. It pushes against the pressure-plate springs, thus freeing the clutch disc. This halts the flow of power until the pedal is released. The Ram 3500 manuals come in two operating styles, hydraulic slave cylinder-operated and cable-pulled, although they have the same pressure on, pressure off action. Wear occurs from constant contact, misadjusted cables, contaminated seals, or rough driving habits like riding the pedal. Once damaged, the Release Bearing will broadcast trouble with rattling sounds, pedal vibration, stiff engagement, and hard shifting. If you are a fan of Dodge, you know how crucial it is to replace a worn Release Bearing quickly. A failed unit can damage the flywheel, disc, and plate. To ensure factory-feel transfer from clutch to Release Bearing for every Dodge Ram 3500 clutch, use factory spec thickness, which also keeps high mileage Ram 3500 shifting confidently. The Release Bearing is essential for optimal performance.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ram 3500 Release Bearing at great affordable prices. Moreover, all genuine Dodge Ram 3500 Release Bearing come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Ram 3500 Release Bearing Parts Questions & Experts Answers

Clutch Release Bearing
52087514
Q: How to remove Pressure Plate,Release Bearing and Clutch Fork on Dodge Ram 3500?
A:
To remove the clutch components, begin by raising and securely supporting the vehicle on jack stands. Disconnect the clutch release cylinder from the clutch housing without disconnecting the hydraulic fluid line. Proceed to remove the transmission, leaving the clutch fork and release bearing attached to the clutch housing. To support the clutch disc during removal, insert a clutch alignment tool through the clutch disc hub. Inspect the flywheel and pressure plate for indexing marks; if absent, create your own to ensure proper alignment during installation. Gradually loosen the pressure plate-to-flywheel bolts in a criss-cross pattern and remove them along with the pressure plate and clutch disc. Inspect all components, including the flywheel for defects, clutch disc for wear or damage, release bearing for replacement, and pressure plate for wear or damage. Clean the surfaces thoroughly and reinstall the flywheel. Align the clutch disc and pressure plate with an alignment tool and finger-tighten the pressure plate-to-flywheel bolts. Center the clutch disc using the alignment tool, then gradually tighten the bolts in a criss-cross pattern to the specified torque. Remove the alignment tool, lubricate the release bearing and related parts with high-temperature grease, reinstall the clutch release bearing if removed, and proceed to reinstall the transmission and all previously removed components. Finally, lower the vehicle.