My Garage
My Account
Cart
Genuine Jeep Compass Lash Adjuster
Lash Adjuster Lifter- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
20 Lash Adjusters found
Jeep Compass Lash Adjuster
The Jeep Compass Lash Adjuster automatically sets the small space between cam and valve, ensuring quiet and precise valve movement. Consequently, the engine runs smoothly and lasts longer. The Lash Adjuster operates similarly to hydraulic tappets, with pressurized oil causing it to expand and eliminate clearances as the cam lobe rotates. The valve lash that sets itself in position eliminates the requirement for periodic check-up, reduces wear on rocker arms, and enables consistent breathing at every speed. The early versions of Compass editions all utilized a solid style with fixed shims. The later editions opted for the hydraulic Lash Adjuster for instant response to heat and part growth. The primary distinction is in maintenance, as the solid type requires careful shim replacement, whereas the hydraulic Lash Adjuster quietly adjusts with oil pressure. The reasons why Jeep applied the hydraulic setup on many current Compass engines are fewer cold-start ticks, steadier idle, and longer life. The Lash Adjuster is a small component that helps keep every Jeep engine running smoothly. In addition, with the use of roller lifters, this component also reduces friction and helps improve the efficiency of the Jeep Compass range. This design decision helps keep the rugged spirit linked to the Jeep badge.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Compass Lash Adjuster at great affordable prices. Moreover, all genuine Jeep Compass Lash Adjuster come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Jeep Compass Lash Adjuster Parts Questions & Experts Answers
- Q: What are the steps, precautions, and tools required for removing and reinstalling camshafts and Lash Adjuster on Jeep Compass?A:Some care should be taken here as the timing system is a bit intricate and any mistake is likely to result in serious damage to the engine; it is strongly advised that only experts attempt this; where there is any doubt regarding ability, professional advice should be sought. All work should be checked for accuracy before the engine has been started again. The camshafts do not necessarily require the removal of the Timing Chain cover and the timing chain; although it has to be done if the necessary tools for removing the camshafts are not available. First and foremost, the engine cover has to be disconnected and then the negative , battery cable; a nut to the right front wheel has to be unscrewed; the vehicle should be raised on the jack stands, the right front wheel and the drivebelt splash shield to be extracted. After then, drain the engine oil and coolant and remove the drivebelt and the ignition coils and spark plugs and finally take off the valve cover. Turn the crankshaft until electrode No.1 is at TDC on its compression stroke and be sure that timing mark is aligned when timing chain is reinstalled, mark the camshaft phasers for their proper reassembly. Free the timing chain tensioner plug and pop up the plunger ratchet with the help of a pick, and to keep this ratchet, the special tool must be inserted. Slide in a chain holding tool between the two camshaft phasers, this is to ensure that during the phaser removal the holding tool is left in place to avoid 'unlocking' of the timing chain. The camshaft bearing caps are to be marked for right and left so that each one of them can be put in place in the proper direction and the bolts are to be loosened in the sequence in which they were tightened but in a reverse order. Take off the front camshaft bearing cap together with the remaining ones: first lift the intake camshaft upward and then, fix the chain to prevent from dropping. Remove the lower bearing from the exhaust camshaft journal and loosen and remove the bolt that holds the phaser on the camshaft and mark the Lash Adjusters so that you know in which position they go back in from which they come out. Check the condition of the camshaft bearing surfaces and the Lash Adjusters and, in the case of damage, replace the piece. This done by turning the crankshaft manually prior to starting the engine at least two revolutions and feel for any resistance. Screw the phasers onto the camshafts so that the marks face each other and tighten the bolts to the recommended turning moment. Submerge the Lash Adjusters in clean engine oil and then place them back in their proper position; it is also prime time to lubricate the camshaft bearing journals and lobes as well. Align the timing chain over the exhaust phaser sprocket and position the machined scribe lines parallel to the gasket surface, then install the camshafts over Cylinder Head. There should now be no turn on the camshaft and so tighten the camshaft bearing cap and bolts in the manner prescribed with the camshaft bearing cap bolts to the specified torque. Make sure that all the marks are aligned, then, remove the Allen wrench and the holding tool of the chain, and turn the engine for two times to ensure that the marks on the camshaft are lined up. Last, apply antiseize on the timing chain tensioner plug then tighten it and end the process in the reverse taking down manner.
Related Jeep Compass Parts
Browse by Year
2024 Lash Adjuster 2023 Lash Adjuster 2022 Lash Adjuster 2021 Lash Adjuster 2020 Lash Adjuster 2019 Lash Adjuster 2018 Lash Adjuster 2017 Lash Adjuster 2016 Lash Adjuster 2015 Lash Adjuster 2014 Lash Adjuster 2013 Lash Adjuster 2012 Lash Adjuster 2011 Lash Adjuster 2010 Lash Adjuster 2009 Lash Adjuster 2008 Lash Adjuster 2007 Lash Adjuster