How to Properly Install, Replace and Align Your Drive Shaft on Jeep Grand Cherokee?

The manufacturer also advises that during installation one should fit new driveshaft fasteners. Starting on the rear driveshaft: first, slightly lift the vehicle off the ground and firmly set it on jacks. Mark the driveshaft with its mating flange on the differential axle assembly with chalk or scribe so as to align them properly when re-fixing. Take off the bolts that connects the drive shaft flange to the differential pinion flange using a screwdriver through the drive shaft yoke in order not to turn. Shove the flat nut and pull the universal joint from its mating flange and while pulling it, it is also necessary to liberate the caps from the shaft. Lower the rear of the driveshaft; on a one piece driveshaft, remove the front end from the transmission extension housing; on a two piece driveshaft, mark the relationship of the center support bearing to the support bracket, unbolt the support bracket and remove the front end of the driveshaft. Wrap the extension housing with a plastic bag and fasten it with a rubber band to retain the fluids and avoid the effect of contamination. For installation take out the plastic bag, clean the surface and check for leakage in the oil seal. Inspect the center support bearing for roughness or nosie and if so it should be replaced. Place the front part of the extension housing on the driveshaft, lift the rear part of the driveshaft into the proper position and align the alignment marks; turn the pinion flange in or out as required. For a two-piece unit, lift the center support bearing, loosely fasten it and position the rear shaft for coupling. Take out all the tapes that may be used to cover the bearing caps, fit the clamps and fasteners before tightening the bearing caps bolts to the recommended torque for the center support bearing. For the front driveshaft in 4WD, lift the vehicle and support it, removal of the skid plate if it is installed and the exhaust crossover pipe if required. Locate the position of the driveshaft in relation to the differential axle assembly mating flange, loosen and remove the bolts that secure the front end of the driveshaft to the spot-welded flange of the differential axle assembly, and if the truck is fitted with a transfer case flanges, make relative sighting marks on the driveshaft flanges and that of the transfer case. Loosen the two bolts that hold the flange which connects the driveshaft universal joint to the transfer case and pull the driveshaft. To dismantle the transfer case of models with a splined sliding sleeve, turn the dust boot clamp and pull out the driveshaft. Installation is the opposite of removal and involves aligning the vehicle if placed, in Neutral or rotating a wheel, and then properly positioning the universal joint caps to be tighten by using the torque wrench to the required torque.

Genuine Jeep Grand Cherokee Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

130 Drive Shafts found

View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 52853649AF
$2519.00 MSRP: $3845.00
You Save: $1326.00 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece; Drive Shaft
- Replaces: 52853649AC, 52853649AD, 52853649AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Jeep Grand Cherokee | Laredo 4WD, Limited 4WD, Overland 4WD | 8 Cyl 5.7L
View related parts
Jeep Grand Cherokee Drive Shaft
Part Number: 52123811AC
$1040.60 MSRP: $1600.00
You Save: $559.40 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Drive
- Replaced by: 52123811AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2020 Jeep Grand Cherokee | Limited RWD, Overland RWD, Summit RWD
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 52123622AA
$774.40 MSRP: $1190.00
You Save: $415.60 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Position: Rear
- Replaced by: 52123622AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Grand Cherokee | Laredo 2WD, Limited 2WD, Overland 2WD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Front Drive Shaft
Part Number: 52853464AB
$826.10 MSRP: $1265.00
You Save: $438.90 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Drive; Drive Shaft
- Position: Front
- Replaces: 52853464AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Jeep Grand Cherokee | Laredo 4WD, Limited 4WD, Overland 4WD | 6 Cyl 3.0L Diesel, 8 Cyl 6.1L
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 52123627AA
$553.50 MSRP: $1275.00
You Save: $721.50 (57%)
ADD TO CART
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Position: Rear
- Replaced by: 52123627AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Jeep Grand Cherokee | Laredo 4WD, Laredo AWD, Limited 4WD, Limited AWD, Overland 4WD, Overland AWD, Summit AWD, Trailhawk AWD | 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Jeep Grand Cherokee Drive
Part Number: 68206211AC
$789.80 MSRP: $1205.00
You Save: $415.20 (35%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft
- Replaces: 68206211AB, 68206211AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Grand Cherokee | 6 Cyl 3.6 L FLEX
View related parts
Jeep Grand Cherokee Front Drive Shaft
Part Number: 52853641AD
$873.40 MSRP: $1325.00
You Save: $451.60 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Drive
- Replaced by: 52853641AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2018 Jeep Grand Cherokee | Laredo 4WD, Laredo AWD, Limited 4WD, Limited AWD, Overland 4WD, Overland AWD, Summit AWD, Trailhawk AWD | 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 68206210AA
$893.20 MSRP: $1380.00
You Save: $486.80 (36%)
ADD TO CART
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Position: Rear
- Replaced by: 68206210AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2017 Jeep Grand Cherokee | Laredo 4WD, Laredo AWD, Limited 4WD, Limited AWD, Overland 4WD, Overland AWD, Summit AWD, Trailhawk AWD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Drive
Part Number: 52123730AD
$841.50 MSRP: $1275.00
You Save: $433.50 (34%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft
- Replaces: 52123730AB, 52123730AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Grand Cherokee | 6 Cyl 3.6 L FLEX
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 52123730AB
$841.50 MSRP: $1275.00
You Save: $433.50 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Position: Rear
- Replaced by: 52123730AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2017 Jeep Grand Cherokee | Laredo 2WD, Laredo RWD, Limited 2WD, Limited RWD, Overland 2WD, Overland RWD, Summit RWD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 52123631AA
$764.50 MSRP: $1175.00
You Save: $410.50 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Position: Rear
- Replaced by: 52123631AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Grand Cherokee | Laredo 4WD, Limited 4WD, Overland 4WD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Drive
Part Number: 52853641AF
$873.40 MSRP: $1325.00
You Save: $451.60 (35%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft
- Replaces: 52853641AC, 52853641AE, 52853641AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Grand Cherokee | 6 Cyl 3.6 L FLEX
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 68206211AA
$789.80 MSRP: $1205.00
You Save: $415.20 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Replaced by: 68206211AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2017 Jeep Grand Cherokee | Laredo 4WD, Laredo AWD, Limited 4WD, Limited AWD, Overland 4WD, Overland AWD, Summit AWD, Trailhawk AWD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Front Drive Shaft
Part Number: 52853642AD
$343.73 MSRP: $774.00
You Save: $430.27 (56%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Drive
- Replaced by: 52853642AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2018 Jeep Grand Cherokee | Laredo 4WD, Laredo AWD, Limited 4WD, Limited AWD, Overland 4WD, Overland AWD, Summit AWD, Trailhawk AWD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Drive
Part Number: 52123627AC
$813.65 MSRP: $1275.00
You Save: $461.35 (37%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft
- Replaces: 52123627AA, 52123627AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Grand Cherokee | 6 Cyl 3.6 L FLEX
View related parts
Jeep Grand Cherokee Drive
Part Number: 52853642AF
$505.28 MSRP: $774.00
You Save: $268.72 (35%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft
- Replaces: 52853642AE, 52853642AC, 52853642AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Grand Cherokee | 6 Cyl 3.6 L FLEX
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 52123629AA
$715.29 MSRP: $1065.00
You Save: $349.71 (33%)
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Position: Rear
- Replaced by: 52123629AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Grand Cherokee | Laredo 4WD, Limited 4WD, Overland 4WD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Rear Drive Shaft
Part Number: 52123626AA
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Replaced by: 52123626AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Grand Cherokee | Laredo 2WD, Limited 2WD, Overland 2WD | 8 Cyl 5.7L
View related parts
Jeep Grand Cherokee Rear Drive Shaft Replaces
Part Number: 52853645AE
Product Specifications
- Other Name: Shaft Drive Rear 2-Piece
- Position: Rear
- Replaced by: 52853645AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2012 Jeep Grand Cherokee | Laredo 2WD, Limited 2WD, Overland 2WD | 6 Cyl 3.6L
View related parts
Jeep Grand Cherokee Drive Shaft
Part Number: 53010904AA
$1090.45 MSRP: $1625.00
You Save: $534.55 (33%)
Product Specifications
- Other Name: Shaft-Drive
- Replaced by: 53010904AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018 Jeep Grand Cherokee | Limited AWD, Overland AWD, Summit AWD, Trackhawk AWD, Trailhawk AWD | 8 Cyl 6.2L

| Page 1 of 7 |Next >

1-20 of 130 Results

Jeep Grand Cherokee Drive Shaft

The Drive Shaft of Jeep Grand Cherokee vehicles is a very crucial link that helps to convey torques from the engine to the rear wheels. Usually made out of long metal rod, the Drive Shaft is responsible for connecting the transmission assembly to the rear differential assembly so that it works properly. In different models, Drive Shafts may include constant velocity (CV) joints that keeps the shafts turning at the same rate by minimizing stress when the vehicle is in the process of steering. The Rzeppa joint is one of such designs used in these applications which enables large changes in angle but little slippage. Designation of the Drive Shafts have also changed over the years, with Jeep Grand Cherokee vehicles using both the one-piece as well as two-piece Drive Shafts for different models it carries today depending with the type of drivetrain system it carries. These variations are due to the need for different configurations when using couplings on 4x4 and all-wheel drive vehicles where Drive Shafts may be several in order to transmit power and torque efficiently. Any wear or tear on boots and grease leak or cracks at the boots needs to be fixed right on time as it affects the life and reliability of the Jeep Grand Cherokee Drive Shaft.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Grand Cherokee Drive Shaft at great affordable prices. Moreover, all genuine Jeep Grand Cherokee Drive Shaft come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Grand Cherokee Drive Shaft Parts Questions & Experts Answers

Rear Drive Shaft
52123622AA
Q: How to Properly Install, Replace and Align Your Drive Shaft on Jeep Grand Cherokee?
A:
The manufacturer also advises that during installation one should fit new driveshaft fasteners. Starting on the rear driveshaft: first, slightly lift the vehicle off the ground and firmly set it on jacks. Mark the driveshaft with its mating flange on the differential axle assembly with chalk or scribe so as to align them properly when re-fixing. Take off the bolts that connects the drive shaft flange to the differential pinion flange using a screwdriver through the drive shaft yoke in order not to turn. Shove the flat nut and pull the universal joint from its mating flange and while pulling it, it is also necessary to liberate the caps from the shaft. Lower the rear of the driveshaft; on a one piece driveshaft, remove the front end from the transmission extension housing; on a two piece driveshaft, mark the relationship of the center support bearing to the support bracket, unbolt the support bracket and remove the front end of the driveshaft. Wrap the extension housing with a plastic bag and fasten it with a rubber band to retain the fluids and avoid the effect of contamination. For installation take out the plastic bag, clean the surface and check for leakage in the oil seal. Inspect the center support bearing for roughness or nosie and if so it should be replaced. Place the front part of the extension housing on the driveshaft, lift the rear part of the driveshaft into the proper position and align the alignment marks; turn the pinion flange in or out as required. For a two-piece unit, lift the center support bearing, loosely fasten it and position the rear shaft for coupling. Take out all the tapes that may be used to cover the bearing caps, fit the clamps and fasteners before tightening the bearing caps bolts to the recommended torque for the center support bearing. For the front driveshaft in 4WD, lift the vehicle and support it, removal of the skid plate if it is installed and the exhaust crossover pipe if required. Locate the position of the driveshaft in relation to the differential axle assembly mating flange, loosen and remove the bolts that secure the front end of the driveshaft to the spot-welded flange of the differential axle assembly, and if the truck is fitted with a transfer case flanges, make relative sighting marks on the driveshaft flanges and that of the transfer case. Loosen the two bolts that hold the flange which connects the driveshaft universal joint to the transfer case and pull the driveshaft. To dismantle the transfer case of models with a splined sliding sleeve, turn the dust boot clamp and pull out the driveshaft. Installation is the opposite of removal and involves aligning the vehicle if placed, in Neutral or rotating a wheel, and then properly positioning the universal joint caps to be tighten by using the torque wrench to the required torque.