How to disconnect and adjust the brake light switch on Jeep Wrangler?

Disconnect the cable from the negative terminal of the battery. For models from 2001 and earlier, unplug the brake light switch electrical connector from under the dash and remove the pushrod bolt or retaining clip, then take out the brake light switch while noting the positions of the bushings, spacers, and sleeves. Lubricate these components with a light coat of multi-purpose grease, position the switch against the brake pedal, and install the pushrod bolt and nuts or retaining clip, ensuring to tighten the nuts to the specified torque for pre-1991 models. Plug in the electrical connector and reconnect the battery. The switch is not adjustable on pre-1991 models, while it is adjustable on 1991 and later models. To check the adjustment on 1991 and later models, move the brake pedal forward by hand and observe the switch plunger, which should be fully extended when the pedal freeplay is taken up, with a clearance of about 1/8-inch between the plunger and the pedal. If the clearance is correct and the brake lights are functioning, no adjustment is needed; otherwise, adjust the switch if the plunger does not fully extend. Note that for models from 2007 and later, if the brake light switch is removed, it cannot be reused and a new switch must be installed. To adjust the switch, pull the brake pedal to the rear as far as possible, allowing the switch plunger barrel to ratchet to the correct position, then measure the plunger-to-pedal clearance and verify the brake lights are operating correctly. For models from 2012 and later, disconnect the negative battery cable, remove the steering column covers, and disconnect the electrical connector to the brake light switch. While pressing the brake switch with your foot, rotate it counterclockwise about 30 degrees until the locking tabs align, then pull the switch out of the bracket. To install, ensure the brake light switch lever arm is fully extended, push the brake pedal down, align the tabs, and rotate the switch 30 degrees clockwise to lock it in place before reconnecting the electrical connector and reinstalling the steering wheel covers.

Genuine Jeep Wrangler Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Brake Light Switches found

View related parts
Jeep Wrangler Stop Lamp Switch
Part Number: 4671336AD
$42.65 MSRP: $58.00
You Save: $15.35 (27%)
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp
- Replaces: 4671336AB, 4671336AC, 4671336
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2018 Jeep Wrangler | 70th Anniversary, Rubicon, Rubicon 4WD, Sahara, Sahara 4WD, SE, Sport, Sport 4WD, Unlimited, Unlimited Rubicon, Unlimited Rubicon 4WD, Unlimited Sahara 2WD, Unlimited Sahara 4WD, Unlimited Sport 2WD, Unlimited Sport 4WD, Unlimited X 2WD, Unlimited X 4WD, Unlimited X RHD 4WD, X, X RHD | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Stop Lamp Switch
Part Number: 4671336
$42.65 MSRP: $58.00
You Save: $15.35 (27%)
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp
- Replaced by: 4671336AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2006 Jeep Wrangler | Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Sensor-Brake Pedal
Part Number: 68361455AC
$49.51 MSRP: $71.15
You Save: $21.64 (31%)
ADD TO CART
Product Specifications
- Other Name: Stoplamp Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | Rubicon 4WD, Sport 4WD, Unlimited Rubicon 4WD, Unlimited Sahara 4WD, Unlimited Sport 4WD, Unlimited Sport RHD 4WD | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.0L, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.0L Diesel, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6L, 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Stop Lamp Switch
Part Number: 4671336AC
$40.54 MSRP: $58.00
You Save: $17.46 (31%)
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp
- Replaced by: 4671336AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013 Jeep Wrangler | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara 4WD, Unlimited Sport 4WD | 6 Cyl 3.6L
View related parts
Jeep Wrangler Stop Lamp Switch
Part Number: 4671336AB
$40.54 MSRP: $58.00
You Save: $17.46 (31%)
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp
- Replaced by: 4671336AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2012 Jeep Wrangler | 70th Anniversary, Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara 2WD, Unlimited Sahara 4WD, Unlimited Sport 2WD, Unlimited Sport 4WD, Unlimited X 2WD, Unlimited X 4WD, Unlimited X RHD 4WD, X, X RHD | 6 Cyl 3.6L, 6 Cyl 3.8L
View related parts
Jeep Wrangler Sensor-Brake Pedal
Part Number: 68361455AB
$49.51 MSRP: $71.15
You Save: $21.64 (31%)
ADD TO CART
Product Specifications
- Other Name: Stoplamp Switch
- Replaced by: 68361455AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018 Jeep Wrangler | Rubicon 4WD, Sport 4WD, Unlimited Rubicon 4WD, Unlimited Sahara 4WD, Unlimited Sport 4WD | 4 Cyl 2.0L, 6 Cyl 3.6L
View related parts
Jeep Wrangler Switch-START/STOP
Part Number: 68089463AA
$75.60 MSRP: $115.00
You Save: $39.40 (35%)
ADD TO CART
Product Specifications
- Other Name: Switch Start/Stop; Neutral Safety Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2018 Jeep Wrangler
View related parts
Jeep Wrangler Switch, Brake Lamp
Part Number: J3225787
Product Specifications
- Other Name: Stoplamp Switch, Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1990 Jeep Wrangler | 4 Cyl 2.5L, 6 Cyl 4.2L
View related parts
Jeep Wrangler Switch, Stop Lamp
Part Number: 56006981
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1995 Jeep Wrangler | Sport Utility 4WD | 4 Cyl 2.5L, 6 Cyl 4.0L

Jeep Wrangler Brake Light Switch

The Brake Light Switch in Jeep line up of Manufactured vehicles Jeep Wrangler is a safety mechanism that is meant to switch on the brake light whenever the brake pedal is pressed. This function is very important since drivers of vehicles behind the Jeep Wrangler will be informed by the amount of light that the vehicle is slowing down or even coming to a standstill. Over the years, different models of Jeep Wrangler may have utilized various types of Brake Light Switches, though the primary goal remains consistent: so as to improve the vehicular safety common features such as brake lights are used in the communication of status. Although all the Brake Light Switch styles are designed to fulfill the same basic function, the design or the way it can be incorporated may vary from model year to model year of Jeep Wrangler. Knowing how Jeep Wrangler Brake Light Switch works and how to take care of it is important since it can fail to work efficiently and this may cause problems of activating brake lights thus posing a threat of an accident.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Wrangler Brake Light Switch at great affordable prices. Moreover, all genuine Jeep Wrangler Brake Light Switch come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Wrangler Brake Light Switch Parts Questions & Experts Answers

Stop Lamp Switch
4671336AB
Q: How to disconnect and adjust the brake light switch on Jeep Wrangler?
A:
Disconnect the cable from the negative terminal of the battery. For models from 2001 and earlier, unplug the brake light switch electrical connector from under the dash and remove the pushrod bolt or retaining clip, then take out the brake light switch while noting the positions of the bushings, spacers, and sleeves. Lubricate these components with a light coat of multi-purpose grease, position the switch against the brake pedal, and install the pushrod bolt and nuts or retaining clip, ensuring to tighten the nuts to the specified torque for pre-1991 models. Plug in the electrical connector and reconnect the battery. The switch is not adjustable on pre-1991 models, while it is adjustable on 1991 and later models. To check the adjustment on 1991 and later models, move the brake pedal forward by hand and observe the switch plunger, which should be fully extended when the pedal freeplay is taken up, with a clearance of about 1/8-inch between the plunger and the pedal. If the clearance is correct and the brake lights are functioning, no adjustment is needed; otherwise, adjust the switch if the plunger does not fully extend. Note that for models from 2007 and later, if the brake light switch is removed, it cannot be reused and a new switch must be installed. To adjust the switch, pull the brake pedal to the rear as far as possible, allowing the switch plunger barrel to ratchet to the correct position, then measure the plunger-to-pedal clearance and verify the brake lights are operating correctly. For models from 2012 and later, disconnect the negative battery cable, remove the steering column covers, and disconnect the electrical connector to the brake light switch. While pressing the brake switch with your foot, rotate it counterclockwise about 30 degrees until the locking tabs align, then pull the switch out of the bracket. To install, ensure the brake light switch lever arm is fully extended, push the brake pedal down, align the tabs, and rotate the switch 30 degrees clockwise to lock it in place before reconnecting the electrical connector and reinstalling the steering wheel covers.

Related Jeep Wrangler Parts

Browse by Year