Make sure this part fits

Mopar 4892425AA Water Pump

2007-2010 Mopar 4892425AA

Customer Questions & Expert Answers (7)
4892425AA Mopar Water Pump Product Photo 1 of 4
  • Part Description
    Pump-Water
  • Manufacturer
    Mopar
Make sure this part fits
$145.13 MSRP: $215.00
You Save: $69.87 (33%)
1
ADD TO CART
  • Related Parts
  • Specifications
  • Fitment
  • Q&A
  • Product Specifications

    BrandGenuine Mopar
    Manufacturer Part Number4892425AA
    Part DescriptionPump-Water
    Item Dimensions4.7 x 6.7 x 8.5 inches
    Item Weight2.90 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerMopar
    SKU4892425AA
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2008-2010 Chrysler 3006 Cyl 2.7LC AWD, C RWD, LX RWD, Touring RWD
    2007-2010 Chrysler Sebring6 Cyl 2.7LLimited Convertible, Limited Sedan, LX Convertible, LX Sedan, Touring Convertible, Touring Sedan
    2007-2010 Dodge Avenger6 Cyl 2.7LExpress, Heat, R/T FWD, SE, SXT
    2008-2010 Dodge Charger6 Cyl 2.7LBase RWD, R/T AWD, R/T RWD
    2009-2010 Dodge Journey6 Cyl 2.7LSE FWD, SXT FWD
    2008 Dodge Magnum6 Cyl 2.7LSE RWD
  • Customer Questions & Expert Answers

    Q:
    Is this part guaranteed to fit my truck ? Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 4892425AA fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Installation and Repair Tips
    Q:
    How to Replace a Water Pump on a Dodge Magnum? Posted by Customer
    A:
    Disconnect the cable from the negative battery terminal. Drain the cooling system and save the coolant if it is in good condition. Remove the engine cooling fan assembly. Remove the drivebelt. For 2.7L V6 engines, remove the timing chain and guides. For 3.5L V6 engines, remove the timing belt. For 5.7L VS engines, remove the thermostat. Detach the radiator hose from the water pump and remove the idler pulley for the drivebelt. Remove the water pump from the engine, noting the locations of the bolts. Clean the bolt threads and threaded holes. Compare the new pump to the old one and check the impeller blades for corrosion. Remove old gasket material or O-ring seal. Clean the mating surfaces with lacquer thinner or acetone. Apply RTV sealant to the new water pump O-ring or gasket. Attach the pump to the engine and tighten the bolts in a criss-cross pattern. Connect the hoses and reinstall all removed parts. Refill the cooling system, run the engine, and check for leaks.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be checked if coolant is leaking from the front of the 2009 Chrysler 300, particularly the Water Pump? Posted by Customer
    A:
    On 3.5L V6 engines, if you notice coolant under the front of the vehicle, look at the bottom of the lower timing belt cover (behind the crankshaft pulley). Coolant leaks in this area usually indicate a failing water pump seal.
    Posted by MoparPartsGiant Specialist
    Q:
    What steps should be taken before removing the Water Pump for the 2009 Chrysler Sebring? Posted by Customer
    A:
    Set the parking brake, raise the front of the vehicle and support it securely on jackstands. Drain the cooling system.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be done before installing the new Water Pump for the 2009 Dodge Avenger? Posted by Customer
    A:
    Clean the bolt threads and threaded holes in the timing case cover. Compare the new pump to the old one. Remove all traces of old gasket material or the O-ring seal. Clean the engine and water pump mating surfaces. Apply a thin coat of RTV sealant to the new water pump O-ring and position it in the groove on the back of the water pump.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be checked if coolant is leaking from the front of the 2009 Dodge Charger, including the Water Pump? Posted by Customer
    A:
    On 3.5L V6 engines, if you notice coolant under the front of the vehicle, look at the bottom of the lower timing belt cover (behind the crankshaft pulley). Coolant leaks in this area usually indicate a failing water pump seal.
    Posted by MoparPartsGiant Specialist
    Q:
    What do you need to do after reinstalling all removed parts, including the Water Pump, for the 2008 Dodge Charger? Posted by Customer
    A:
    Refill the cooling system, run the engine, and check for leaks.
    Posted by MoparPartsGiant Specialist
    See Complete Installation and Repair Tips

Genuine Mopar Part 4892425AA, the Right Choice

To ensure reliability, purchase Mopar part # 4892425AA Water Pump. It is sometimes referred to as Water Pump. The OEM parts should be used when the Mopar owners want to maximize their driving experience. The high-tech factories that produce these parts utilize sophisticated technology specifically designed to meet stringent factory requirements. Additionally, they are thoroughly tested and can thus be used with reliability by Mopar owners. This part fits specific Chrysler 300 and Sebring models. It fits Dodge Charger, Journey, Magnum.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as 4892425AA Water Pump. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at attractive prices. Further, all parts come with a manufacturer's warranty. For detailed Dodge parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly