Mopar 5083344AA Sw Pkg-Stop Lamp

If the brake lights are not working, check the fuse first. If the fuse is good, check for voltage to the switch on the feed wire.

To troubleshoot, check the brake light fuse and replace if necessary. Verify voltage to the switch and repair any open or short in the power wire. If the brake lights still don't come on, test for continuity between the switch terminals when the brake pedal is applied and replace the switch if continuity is not detected. If there is continuity but the brake lights still don't come on, check for power to the brake light bulb sockets and replace the bulbs if voltage is present. If voltage is not available, check the wiring between the switch and the brake lights for an open circuit and repair as necessary.

To replace the switch, disconnect the negative battery cable, rotate the switch counterclockwise to remove it from the mounting bracket, unplug the electrical connector, and discard the old switch. Pull the plunger out on the new switch, depress the brake pedal, and install the switch into the bracket by aligning the slots and rotating it clockwise. Release the brake pedal to ensure it is seated properly and plug in the electrical connector. Reconnect the battery and test the brake lights for proper operation.

The brake light switch is mounted on a bracket supporting the steering column.

Once the switch is removed, it must be replaced with a new one. The switch can only be installed once.

Depress the brake pedal and use the test light to check for voltage in the wire between the switch and the brake lights. If there is voltage, it indicates that the switch is functioning normally, and the issue likely lies somewhere between the switch and the brake lights. If there is no voltage, it suggests that the switch has an open and should be replaced.

For installation, depress the brake pedal fully, align the switch with the bracket, and avoid excessive force to prevent damage. Once installed, rotate the switch clockwise to lock it in place, gently pull back on the brake pedal until it stops to allow the plunger to ratchet to the correct position, and finally plug the electrical connector back into the switch.

To troubleshoot brake light issues, first check the brake light fuse and address any shorts in the circuit if the fuse has blown. Verify voltage to the switch using a test light or voltmeter and repair any power wire issues if voltage is absent. If the brake lights still don't illuminate when the pedal is pressed, perform continuity testing at the switch terminals. If continuity is not detected, replace the switch. If continuity exists but the lights remain off, further inspect power and ground connections at the bulb sockets and wiring leading to the Totally Integrated Power Module (TIPM) under the hood. Seek professional assistance if the issue appears to involve the TIPM, as some may require programming after replacement. For the center high-mounted stop lamp, which is independent of the TIPM, ensure the switch, leads, sockets, and bulbs are in working order.

Hold the brake pedal down and insert the new switch into its bracket until it's properly seated, then turn it counterclockwise to lock it in place. Let go of the brake pedal, but don't pull it up. Turn the plunger release lever clockwise until it snaps into place. Make sure the switch is seated properly before moving the lever. If an error is made, the switch will have to be discarded and replaced with a new one.

Hold the brake pedal down and insert the new switch into its bracket until it's properly seated, then turn it counterclockwise to lock it in place. Let go of the brake pedal, but don't pull it up. Turn the plunger release lever clockwise until it snaps into place. Make sure the switch is seated properly before moving the lever. If an error is made, the switch will have to be discarded and replaced with a new one.

Disconnect the wiring from the switch and hold the brake pedal down, then turn the switch slightly clockwise and pull it from its bracket.

To check the switch, remove the lower trim panel from the dash and disconnect the wiring. Use an ohmmeter to test the continuity of the switch terminals.

To replace the brake light switch, first disconnect the battery, then depress the brake pedal, remove the old switch, unplug its connector, and discard it. Extend the plunger on the new switch, depress the brake pedal again, install the switch into the bracket, and rotate it clockwise. Ensure the brake pedal is properly seated against the pedal striker, allowing the switch plunger to ratchet backward to its correct position. Plug in the electrical connector, reconnect the battery, and test the brake lights for proper operation.