How to Check and Replace Engine Mounts on Jeep Compass?

There are four powertrain mounts, The front mount sustains the transaxle to the cross member, the left mount bonds the driver side of the engine to the sub frame, the right engine mount links the engine block to the passenger side of the sub frame and the rear mount also links the engine block to the sub frame. For this the engine has to be lifted from the mounts slightly to take weight off the mounts for examination. First safely chock the car and then elevate the car and support it with jack stands and remove the front wheels and tires. Place one jack under crankshaft pulley and the other at the bottom of transaxle bellhousing putting a piece of wood or metal over both points where the jacks will be placed to protect the components while lifting the engine/transaxle just enough to relieve the mounts. With reference to the previous description there are several items that should first be looked at: The mounts should be examined for any cracking of rubber or metal, the rubber becoming hardened or if the rubber and metal sleeve are still fused together The amount of relative movement between the mount bracket and the engine, subframe or chassis should be tested using a large screwdriver or prybar. If movement is noticed, reduce the engine and loosen the mount bolts. During the front mount replacement, place a block of wood underneath the engine oil pan, disconnect the splash shield, front mount through-bolt as well as the crossmember-to-mount bolts before finally removing the mount. If the mount bracket has to be replaced, the bracket-to-block bolts will have to be removed. Disassembly too is done in the reverse order, while making certain that all the bolts and screws are tightened to the required degree. The left mount is controlled by the following process: The negative battery cable is disconnected, the air filter housing is taken off and the transaxle is supported while it is lifted to reduce the load on the mount. Take out the mount through-bolt and the mount to chassis bolts then just reverse the process and tighten the bolts to the recommended torque. If the right mount is involved, the coolant reservoir, power steering fluid reservoir, and windshield washer fluid reservoir has to be detached to get to the engine mount. Support the engine, loosen the through-bolt 7146 which joins the two engine mounts together and further the bolts 7140 you need for the removal of the mount bracket and mount from their positions. It is installed in a manner that will undo the disassembly, making sure that every bolt has been secured to the necessary tightness. For the rear mount, lift the car, first, loosen and then remove the engine splash guard and the downstream oxygen sensor then support the engine and disconnected the rear mount through bolt and mount to cross member bolts. Place the new mount into the bracket, line up with the crossmember and tighten all bolts to the required torque tightening in the reverse of the removal process.

Genuine Jeep Compass Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

69 Engine Mounts found

View related parts
Jeep Compass Engine Mount Bracket
Part Number: 68267889AA
$113.35 MSRP: $238.00
You Save: $124.65 (53%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Side Mount Bracket
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2019 Jeep Compass | Latitude AWD, Sport AWD, Sport FWD
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 68328737AB
$194.63 MSRP: $291.00
You Save: $96.37 (34%)
ADD TO CART
Product Specifications
- Other Name: INSULATOR-Engine Mount; Isolator, Side Mount
- Position: Passenger Side
- Replaces: 68328737AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2022 Jeep Compass | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4 L GAS, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 68328737AA
$194.63 MSRP: $291.00
You Save: $96.37 (34%)
ADD TO CART
Product Specifications
- Other Name: INSULATOR-Engine Mount
- Replaced by: 68328737AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2019 Jeep Compass | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Bracket
Part Number: 68253048AB
$48.52 MSRP: $69.85
You Save: $21.33 (31%)
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mount; Support
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2022 Jeep Compass | 80th Spec. Edition AWD, Latitude AWD, Limited AWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4 L GAS, 4 Cyl 2.4L
View related parts
Jeep Compass Transmission Mount Isolator
Part Number: 68253034AB
$180.00 MSRP: $272.00
You Save: $92.00 (34%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR-Transmission Mount
- Replaced by: 68253034AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2020 Jeep Compass | Latitude AWD, Limited AWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Compass Support
Part Number: 68195033AB
$69.92 MSRP: $105.00
You Save: $35.08 (34%)
ADD TO CART
Product Specifications
- Other Name: Engine Mount Rear
- Replaced by: 68195033AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2017 Jeep Compass | Latitude FWD, Limited FWD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105489AI
$249.76 MSRP: $377.00
You Save: $127.24 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 5105489AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Jeep Compass | Latitude 4WD, Latitude FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105489AH
$249.76 MSRP: $377.00
You Save: $127.24 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 5105489AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2014 Jeep Compass | Latitude 4WD, Latitude FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Support
Part Number: 68032586AF
$81.39 MSRP: $123.00
You Save: $41.61 (34%)
ADD TO CART
Product Specifications
- Other Name: Engine Mount Rear
- Replaced by: 68032586AH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Jeep Compass | Base FWD, Latitude FWD, Limited FWD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105489AG
$249.76 MSRP: $377.00
You Save: $127.24 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 5105489AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2012 Jeep Compass | Base 4WD, Base FWD, Latitude 4WD, Latitude FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Bracket
Part Number: 5105409AE
$51.84 MSRP: $74.45
You Save: $22.61 (31%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Mount Bracket, Support Bracket
- Replaces: 5105409AD, 5105409AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2017 Jeep Compass | Base 4WD, Latitude 4WD, Limited 4WD, Sport 4WD | 4 Cyl 2.4L
- 2007-2008 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD | 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Support
Part Number: 5105290AC
$153.00 MSRP: $231.00
You Save: $78.00 (34%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount; Engine Support, Mount Support
- Replaces: 5105290AB, 5105290AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2017 Jeep Compass | Base 4WD, Base FWD, Latitude 4WD, Latitude FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105667AG
$110.25 MSRP: $164.00
You Save: $53.75 (33%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 68309249AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Compass | Base 4WD, Base FWD, Latitude 4WD, Latitude FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105489AD
$249.76 MSRP: $377.00
You Save: $127.24 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 5105489AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105667AD
$110.25 MSRP: $164.00
You Save: $53.75 (33%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 68309249AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105667AC
$110.25 MSRP: $164.00
You Save: $53.75 (33%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 68309249AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine
Part Number: 68445486AD
$342.10 MSRP: $522.00
You Save: $179.90 (35%)
ADD TO CART
Product Specifications
- Other Name: Front Mount, Isolator, Side Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023-2025 Jeep Compass | 4 Cyl 2.0 L GAS
View related parts
Jeep Compass Transmission Mount
Part Number: 68445487AD
$273.18 MSRP: $411.00
You Save: $137.82 (34%)
ADD TO CART
Product Specifications
- Other Name: Isolator, Mount, Side Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023-2025 Jeep Compass | 4 Cyl 2.0 L GAS
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105667AF
$110.25 MSRP: $164.00
You Save: $53.75 (33%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 68309249AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Mount Insulator
Part Number: 5105489AF
$249.76 MSRP: $377.00
You Save: $127.24 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 5105489AK
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD, Sport FWD | 4 Cyl 2.4L

| Page 1 of 4 |Next >

1-20 of 69 Results

Jeep Compass Engine Mount

The Engine Mount in Jeep Compass vehicles serves two primary functions: it isolates the noise and the vibrations produced by the engine operation and at the same time locates and supports the engine and transaxle within the chassis. This isolation is important in creating the comfort but positioning of the engine is very important for safety and to prevent damages on parts. Appearing in Jeep Compass generations, the Engine Mounts include simple rubber ones, fluid hydro mounts, and electronics updated active mounts. The old fashioned mounts are made of metal parts which are isolated by rubber spacers whereas hydraulic mount has capability to absorb more of the vibrations. The newest active mounts adapt their torsional stiffness according to the rpm value, which improved the cars' performance. Engine Mounts themselves can get weak over time due to factors such as age, heat, or if they have come in contact with any sort of fluid, one may notice things such as excessive noise or vibration, so they may need to be checked on for failure and then replaced if necessary.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Compass Engine Mount at great affordable prices. Moreover, all genuine Jeep Compass Engine Mount come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Compass Engine Mount Parts Questions & Experts Answers

Engine Mount Insulator
5105489AG
Q: How to Check and Replace Engine Mounts on Jeep Compass?
A:
There are four powertrain mounts, The front mount sustains the transaxle to the cross member, the left mount bonds the driver side of the engine to the sub frame, the right engine mount links the engine block to the passenger side of the sub frame and the rear mount also links the engine block to the sub frame. For this the engine has to be lifted from the mounts slightly to take weight off the mounts for examination. First safely chock the car and then elevate the car and support it with jack stands and remove the front wheels and tires. Place one jack under Crankshaft Pulley and the other at the bottom of transaxle bellhousing putting a piece of wood or metal over both points where the jacks will be placed to protect the components while lifting the engine/transaxle just enough to relieve the mounts. With reference to the previous description there are several items that should first be looked at: The mounts should be examined for any cracking of rubber or metal, the rubber becoming hardened or if the rubber and metal sleeve are still fused together The amount of relative movement between the mount bracket and the engine, subframe or chassis should be tested using a large screwdriver or prybar. If movement is noticed, reduce the engine and loosen the mount bolts. During the front mount replacement, place a block of wood underneath the engine Oil Pan, disconnect the splash shield, front mount through-bolt as well as the crossmember-to-mount bolts before finally removing the mount. If the mount bracket has to be replaced, the bracket-to-block bolts will have to be removed. Disassembly too is done in the reverse order, while making certain that all the bolts and screws are tightened to the required degree. The left mount is controlled by the following process: The negative battery cable is disconnected, the air filter housing is taken off and the transaxle is supported while it is lifted to reduce the load on the mount. Take out the mount through-bolt and the mount to chassis bolts then just reverse the process and tighten the bolts to the recommended torque. If the right mount is involved, the coolant reservoir, power steering fluid reservoir, and windshield washer fluid reservoir has to be detached to get to the engine mount. Support the engine, loosen the through-bolt 7146 which joins the two engine mounts together and further the bolts 7140 you need for the removal of the mount bracket and mount from their positions. It is installed in a manner that will undo the disassembly, making sure that every bolt has been secured to the necessary tightness. For the rear mount, lift the car, first, loosen and then remove the engine splash guard and the downstream oxygen sensor then support the engine and disconnected the rear mount through bolt and mount to cross member bolts. Place the new mount into the bracket, line up with the crossmember and tighten all bolts to the required torque tightening in the reverse of the removal process.