How to measure and adjust the exhaust valve and intake valve clearance on Jeep Compass?

Position the number 1 piston at TDC on the compression stroke. Remove the engine cover by pulling it up and off of the ballstuds. Disconnect the cable from the negative terminal of the battery. Blow out the recessed area around the spark plug openings with compressed air, if available, to remove any debris that might fall into the cylinders, then remove the spark plugs. Remove the valve cover. The lobes must be measured one set at a time. Rotate the camshaft(s) until two lobes on any one cylinder are pointing straight up and measure the clearances of those valves with feeler gauges. Record any measurements that don't fall within the specified range, as these will be used later to determine the required replacement lifters. Rotate the camshaft(s) until all the lobes have been checked. Remove the camshaft(s) for the valve(s) that you intend to adjust. Remove and measure each lifter with a micrometer, putting each lifter back into its bore in the cylinder head before moving on to the next lifter, and record the measurement for each lifter. To calculate the correct thickness of a replacement lifter that will put the valve clearance within the specified range, use the formula S - C = change, where S is the specified valve clearance and C is the measured valve clearance. Remove the lifter and read the size from the bottom of the lifter, then reduce the lifter by subtracting the specified valve clearance from the measured valve clearance or as close as possible to the calculated size. Install the camshaft(s) and check the valve clearances again to verify that they're now within the range. The remainder of installation is the reverse of removal.

Genuine Jeep Compass Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Intake Valves found

View related parts
Jeep Compass Engine Intake Valve
Part Number: 4892676AB
$20.97 MSRP: $30.25
You Save: $9.28 (31%)
ADD TO CART
Product Specifications
- Other Name: Valve Engine Intake; Intake Valve
- Replaces: 4892676AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2019 Jeep Compass | Latitude AWD, Sport AWD, Sport FWD
View related parts
Jeep Compass Intake Valve
Part Number: 5047446AA
$18.00 MSRP: $26.10
You Save: $8.10 (32%)
ADD TO CART
Product Specifications
- Other Name: Valve Intake Standard
- Replaced by: 68453301AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2019 Jeep Compass | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Compass Engine Intake
Part Number: 68453301AA
$18.00 MSRP: $26.10
You Save: $8.10 (32%)
ADD TO CART
Product Specifications
- Other Name: Valve
- Replaces: 5047446AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2022 Jeep Compass | 80th Spec. Edition AWD, 80th Spec. Edition FWD, Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4 L GAS, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Intake Valve
Part Number: 5047068AB
$26.39 MSRP: $38.20
You Save: $11.81 (31%)
ADD TO CART
Product Specifications
- Other Name: Valve Engine Intake; Intake Valve, Valve
- Replaces: MN187696, 5047068AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2017 Jeep Compass | Base 4WD, Base FWD, Latitude 4WD, Latitude FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Intake Valve
Part Number: MN187696
$26.39 MSRP: $38.20
You Save: $11.81 (31%)
ADD TO CART
Product Specifications
- Other Name: Valve Engine Intake
- Replaced by: 5047068AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Engine Intake Valve
Part Number: 5047068AA
$26.39 MSRP: $38.20
You Save: $11.81 (31%)
ADD TO CART
Product Specifications
- Other Name: Valve Engine Intake
- Replaced by: 5047068AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Jeep Compass | Base 4WD, Base FWD, Limited 4WD, Limited FWD | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Jeep Compass Intake Valve
Part Number: 68089259AA
$12.07 MSRP: $25.60
You Save: $13.53 (53%)
ADD TO CART
Product Specifications
- Other Name: Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2014 Jeep Compass | Base FWD, Latitude FWD, Limited FWD, Sport FWD
View related parts
Jeep Compass Intake Valve
Part Number: 68263242AA
$6.76 MSRP: $9.70
You Save: $2.94 (31%)
ADD TO CART
Product Specifications
- Other Name: Valve-Intake
- Replaced by: 68369573AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2019 Jeep Compass | Latitude AWD, Sport AWD, Sport FWD
View related parts
Jeep Compass Intake Valve
Part Number: 5048155AB
$12.12 MSRP: $17.55
You Save: $5.43 (31%)
Product Specifications
- Other Name: Valve-Intake; Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023-2024 Jeep Compass | 4 Cyl 2.0 L GAS
View related parts
Jeep Compass Engine Intake Valve
Part Number: 68275166AA
$9.38 MSRP: $13.45
You Save: $4.07 (31%)
Product Specifications
- Other Name: Valve-Engine Intake
- Replaced by: 68647244AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2019 Jeep Compass | Latitude AWD, Sport AWD, Sport FWD
View related parts
Jeep Compass Intake Valve
Part Number: 68001582AA
Product Specifications
- Other Name: Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Jeep Compass | Base FWD

Jeep Compass Intake Valve

Jeep Compass automobiles contain an Intake Valve that has a major function of boosting the power of an engine whilst fuel combustion. Its main task is to control the time for admission of air and fuel mixture to the engine which characterizes its power and productivity. Intake Valve can fail to work and result in poor combustion of the engine power and therefore have to be replaced to avoid expensive repairs. Different types of Intake Valves for Jeep Compass have been employed over the years in order to fulfill particular levels of performance. Several steps used when one is replacing a damaged Intake Valve include using spring compressor to compress the valve spring so as to ensure the new valve is fitted properly. Proper installation must be performed to eliminate problems like valve looseness so that Jeep Compass could function well.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Compass Intake Valve at great affordable prices. Moreover, all genuine Jeep Compass Intake Valve come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Compass Intake Valve Parts Questions & Experts Answers

Engine Intake Valve
5047068AB
Q: How to measure and adjust the exhaust valve and intake valve clearance on Jeep Compass?
A:
Position the number 1 piston at TDC on the compression stroke. Remove the engine cover by pulling it up and off of the ballstuds. Disconnect the cable from the negative terminal of the battery. Blow out the recessed area around the spark plug openings with compressed air, if available, to remove any debris that might fall into the cylinders, then remove the spark plugs. Remove the valve cover. The lobes must be measured one set at a time. Rotate the Camshaft(s) until two lobes on any one cylinder are pointing straight up and measure the clearances of those valves with feeler gauges. Record any measurements that don't fall within the specified range, as these will be used later to determine the required replacement lifters. Rotate the camshaft(s) until all the lobes have been checked. Remove the camshaft(s) for the valve(s) that you intend to adjust. Remove and measure each lifter with a micrometer, putting each lifter back into its bore in the Cylinder Head before moving on to the next lifter, and record the measurement for each lifter. To calculate the correct thickness of a replacement lifter that will put the valve clearance within the specified range, use the formula S - C = change, where S is the specified valve clearance and C is the measured valve clearance. Remove the lifter and read the size from the bottom of the lifter, then reduce the lifter by subtracting the specified valve clearance from the measured valve clearance or as close as possible to the calculated size. Install the camshaft(s) and check the valve clearances again to verify that they're now within the range. The remainder of installation is the reverse of removal.