How to remove and replace the ignition lock cylinder and ignition switch on the Jeep Grand Cherokee?

Don't confuse this problem with a faulty ignition switch or an ignition lock cylinder; it could be that the transmission shift cable is off the track regarding adjustment. Start by removing the negative cable from the battery and then take off the knee bolster, and upper and lower steering column. Push the brake pedal and turn the ignition lock cylinder by inserting the ignition key to it and shift the lever to the park position. Rotate the ignition key clockwise to the RUN position, insert a small punch, for example, of about flattened part of a standard pen into the hole for the ignition lock cylinder pin, push the pin inwards and, as a result, pull the ignition lock cylinder out of the steering column. Before inserting the ignition lock cylinder, tide the ignition key at the RUN position, thread the ignition lock cylinder into the ignition with its flats seated into the receptacle on the terminal of the lock cylinder bore, and turn it to the right until it locks into the position. As for the ignition switch, however, one has to remove the cable from the negative terminal of the battery and also to deactivate the air bag. The upper and lower steering column covers have to be taken off, then the ignition lock cylinder has to be withdrawn. Remove the screws that connect the clockspring electrical connectors and place the harness to the side. Three various screws have to be undone in order to detach the tilt lever mounting bracket, then: unplug the electrical connector for the ignition switch and, finally, unscrew the mounting screws on the switch. Twist the small locking tab in anti-clockwise direction with respect to the steering column and pull the ignition switch out. For models from 2014 and after equipped with Keyless Ignition Node (KIN) start switch, include the cable(s) from the negative battery terminal(s). On Durango models, the Start/Stop button is not fixed in any way and can be extracted from the instrument panel without removing the whole panel using just a small trim tool. Pull the center instrument trim bezel and again using the plastic trim stick, insert it at the gap where the steering column gap bezel is situated then pry it out until all the clips holding it are disengaged. Tilt the steering column down and pull the bezel and or the panel back as it is situated on the instrument. Take out the start switch bezel screws, then, pull the bezel forward and disconnect the electrical connector of the start switch. Last, take out the KIN start switch mounting screws and pull the module off the bezel, installation procedure is literally done in reverse.

Genuine Jeep Grand Cherokee Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Ignition Switches found

View related parts
Jeep Grand Cherokee Switch-Engine START/STOP
Part Number: 1FU931X9AC
$39.61 MSRP: $56.70
You Save: $17.09 (31%)
ADD TO CART
Product Specifications
- Other Name: Button Engine Start/Stop; Ignition Switch, Power Switch, Start Button
- Replaces: 1FU931X9AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Limited 2WD, Limited 4WD, Overland 2WD, Overland 4WD, SRT8 4WD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
- 2009 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Limited 2WD, Limited 4WD, Overland 2WD, Overland 4WD, SRT8 4WD | 6 Cyl 3.0L Diesel, 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 6.1L
View related parts
Jeep Grand Cherokee Module-KEYLESS Ignition Node
Part Number: 68299959AC
$102.66 MSRP: $155.00
You Save: $52.34 (34%)
ADD TO CART
Product Specifications
- Replaces: 68207000AC, 68299959AA, 68207000AD, 68299959AB, 1KW59DX9AC, 68207000AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2022 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Laredo AWD, Laredo RWD, Limited 2WD, Limited 4WD, Limited AWD, Limited RWD, Overland 2WD, Overland 4WD, Overland AWD, Overland RWD, SRT AWD, Summit AWD, Summit RWD, Trackhawk AWD, Trailhawk AWD | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0L Diesel, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Ignition Switch
Part Number: 4685719AB
$63.51 MSRP: $94.40
You Save: $30.89 (33%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition
- Replaced by: 4685719AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Limited 2WD, Limited 4WD, Overland 2WD, Overland 4WD, SRT8 4WD | 6 Cyl 3.0L Diesel, 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 6.1L
View related parts
Jeep Grand Cherokee Module-KEYLESS Ignition Node
Part Number: 68299959AB
$102.66 MSRP: $155.00
You Save: $52.34 (34%)
ADD TO CART
Product Specifications
- Other Name: Module Keyless Ignition Node
- Replaced by: 68299959AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Jeep Grand Cherokee | Laredo AWD, Laredo RWD, Limited AWD, Limited RWD, Overland AWD, Overland RWD, SRT AWD, Summit AWD, Summit RWD, Trackhawk AWD, Trailhawk AWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Ignition Switch Module
Part Number: 68207000AB
$102.66 MSRP: $155.00
You Save: $52.34 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition Push Button
- Replaced by: 68299959AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Limited 2WD, Limited 4WD, Overland 2WD, Overland 4WD, SRT AWD, Summit AWD, Summit RWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Ignition Switch
Part Number: 56042476AC
$86.01 MSRP: $129.00
You Save: $42.99 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition; Ignition Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2004 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Limited 2WD, Limited 4WD, Overland 2WD, Overland 4WD, Sport 2WD, Sport 4WD | 6 Cyl 4.0L, 8 Cyl 4.7L
View related parts
Jeep Grand Cherokee Ignition Switch
Part Number: 68207000AD
$102.66 MSRP: $155.00
You Save: $52.34 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition Push Button
- Replaced by: 68299959AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2016 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Laredo AWD, Laredo RWD, Limited 2WD, Limited 4WD, Limited AWD, Limited RWD, Overland 2WD, Overland 4WD, Overland AWD, Overland RWD, SRT AWD, Summit AWD, Summit RWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Switch-KEYLESS Ignition Node
Part Number: 68299963AB
$90.68 MSRP: $137.00
You Save: $46.32 (34%)
ADD TO CART
Product Specifications
- Other Name: Module Keyless Ignition Node
- Replaced by: 68299963AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Jeep Grand Cherokee | Laredo AWD, Laredo RWD, Limited AWD, Limited RWD, Overland AWD, Overland RWD, SRT AWD, Summit AWD, Summit RWD, Trackhawk AWD, Trailhawk AWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Ignition Switch Module
Part Number: 68299958AC
$89.27 MSRP: $134.00
You Save: $44.73 (34%)
ADD TO CART
Product Specifications
- Other Name: Module-Ignition Switch; Power Switch
- Replaces: 68299958AB, 68197922AA, 68197922AB, 68299958AA, 68197922AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Limited 2WD, Limited 4WD, Overland 2WD, Overland 4WD, SRT AWD, Summit AWD, Summit RWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee IGNITION SWITCH
Part Number: 68532303AA
$97.54 MSRP: $145.00
You Save: $47.46 (33%)
ADD TO CART
Product Specifications
- Other Name: Power Switch, Start Button
- Replaces: 68379775AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022-2023 Jeep Grand Cherokee | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Jeep Grand Cherokee Ignition Switch Module
Part Number: 68577144AB
$90.51 MSRP: $135.00
You Save: $44.49 (33%)
ADD TO CART
Product Specifications
- Other Name: MODULE-IGNITION SWITCH; Power Switch, Start Button
- Replaces: 68577144AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2024-2025 Jeep Grand Cherokee | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Jeep Grand Cherokee Switch-KEYLESS Ignition Node
Part Number: 68299963AC
$90.68 MSRP: $137.00
You Save: $46.32 (34%)
ADD TO CART
Product Specifications
- Other Name: Power Switch
- Replaces: 5035461AA, 68299963AA, 68299963AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2021 Jeep Grand Cherokee | Laredo AWD, Laredo RWD, Limited AWD, Limited RWD, Overland AWD, Overland RWD, SRT AWD, Summit AWD, Summit RWD, Trackhawk AWD, Trailhawk AWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Ignition Switch
Part Number: 68240163AC
$88.76 MSRP: $133.00
You Save: $44.24 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition Push Button
- Replaced by: 68299962AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015 Jeep Grand Cherokee | Laredo 2WD, Laredo 4WD, Laredo AWD, Laredo RWD, Limited 2WD, Limited 4WD, Overland 2WD, Overland 4WD, Overland AWD, Overland RWD, SRT AWD, Summit AWD, Summit RWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Ignition Switch
Part Number: 5035461AA
$90.68 MSRP: $137.00
You Save: $46.32 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition
- Replaced by: 68299963AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016 Jeep Grand Cherokee | Laredo AWD, Laredo RWD, Limited AWD, Limited RWD, Overland AWD, Overland RWD, SRT AWD, Summit AWD, Summit RWD | 6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Jeep Grand Cherokee Switch-Ign
Part Number: J3250575
Product Specifications
- Other Name: Switch, Ignition Lock; Ignition Switch, Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Jeep Grand Cherokee | 2WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4WD | 6 Cyl 4.0L, 8 Cyl 5.2L
View related parts
Jeep Grand Cherokee SWITCHPKG-Ignition
Part Number: 4797401
Product Specifications
- Other Name: Switch, Ignition Starter
- Replaced by: 4797401AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Jeep Grand Cherokee | 2WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4WD | 6 Cyl 4.0L, 8 Cyl 5.2L
View related parts
Jeep Grand Cherokee None-Ignition Lock Cylinder
Part Number: 5257137
Product Specifications
- Other Name: Driver, Ignition Cylinder, Push to Lock
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1996 Jeep Grand Cherokee | 2WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4WD | 6 Cyl 4.0L, 8 Cyl 5.2L

Jeep Grand Cherokee Ignition Switch

Jeep Grand Cherokee's Ignition Switch is used as a part of starting and charging system and its function is to start the car's engine and even to turn on other electrical devices such as radio or electric window regulators. When the Ignition Switch is used along the key, button or a remote control, the vehicle computer actives the starter solenoid and the ignition parts and thus allows the engine to start. Years of producing Jeep Grand Cherokee have seen production of different models using different styles of Ignition Switch, mechanical keys and the present key-less push button. In the older models there was only a key which unlocks the system while in the newer models there is an immobiliser that checks for a transponder signal. Nevertheless, the Ignition Switch is still easy to fix and usually, it is made to be replaceable for each Jeep Grand Cherokee only.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Grand Cherokee Ignition Switch at great affordable prices. Moreover, all genuine Jeep Grand Cherokee Ignition Switch come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Grand Cherokee Ignition Switch Parts Questions & Experts Answers

Switch-Engine START/STOP
1FU931X9AC
Q: How to remove and replace the ignition lock cylinder and ignition switch on the Jeep Grand Cherokee?
A:
Don't confuse this problem with a faulty ignition switch or an ignition lock cylinder; it could be that the transmission shift cable is off the track regarding adjustment. Start by removing the negative cable from the battery and then take off the knee bolster, and upper and lower steering column. Push the brake pedal and turn the ignition lock cylinder by inserting the ignition key to it and shift the lever to the park position. Rotate the ignition key clockwise to the RUN position, insert a small punch, for example, of about flattened part of a standard pen into the hole for the ignition lock cylinder pin, push the pin inwards and, as a result, pull the ignition lock cylinder out of the steering column. Before inserting the ignition lock cylinder, tide the ignition key at the RUN position, thread the ignition lock cylinder into the ignition with its flats seated into the receptacle on the terminal of the lock cylinder bore, and turn it to the right until it locks into the position. As for the ignition switch, however, one has to remove the cable from the negative terminal of the battery and also to deactivate the air bag. The upper and lower steering column covers have to be taken off, then the ignition lock cylinder has to be withdrawn. Remove the screws that connect the clockspring electrical connectors and place the harness to the side. Three various screws have to be undone in order to detach the tilt lever mounting bracket, then: unplug the electrical connector for the ignition switch and, finally, unscrew the mounting screws on the switch. Twist the small locking tab in anti-clockwise direction with respect to the steering column and pull the ignition switch out. For models from 2014 and after equipped with Keyless Ignition Node (KIN) start switch, include the cable(s) from the negative battery terminal(s). On Durango models, the Start/Stop button is not fixed in any way and can be extracted from the instrument panel without removing the whole panel using just a small trim tool. Pull the center instrument trim bezel and again using the plastic trim stick, insert it at the gap where the steering column gap bezel is situated then pry it out until all the clips holding it are disengaged. Tilt the steering column down and pull the bezel and or the panel back as it is situated on the instrument. Take out the start switch bezel screws, then, pull the bezel forward and disconnect the electrical connector of the start switch. Last, take out the KIN start switch mounting screws and pull the module off the bezel, installation procedure is literally done in reverse.