How to remove and reinstall a cylinder head in four cylinder engine on Jeep Cherokee?

Remove the rocker arms and pushrods. Remove the intake and exhaust manifolds.Remove the drivebelt(s). Unbolt the power steering pump (if equipped) and set it aside without disconnecting the hoses.On air conditioned models, remove the bolt that secures the air conditioning compressor/alternator bracket to the cylinder head, then unbolt the compressor/alternator bracket from the engine. Set the compressor aside without disconnecting the hoses.Label, then disconnect the wire from the coolant temperature sending unit on the cylinder head. Label the spark plug wires and remove the spark plugs.Remove the ten bolts that secure the cylinder head and lift it off the engine. If the head is stuck to the engine block, it may be necessary to tap it with a soft-face hammer or a block of wood and a hammer to break the seal. Stuff clean shop towels into the cylinders. Thoroughly clean the gasket surfaces removing all traces of gasket material. Run an appropriate sized tap into the bolt holes in the cylinder head and run a die over the bolt threads. Ensure all bolt holes are clean and dry.Inspect the cylinder head for cracks and check it for warpage. 1984 through 1987 four-cylinder engines use different head gaskets than 1988 and later models. The two types of gaskets are NOT interchangeable and require different tightening torques.These engines use stamped steel gaskets. Apply an even coat of a copper coat type gasket sealant to both sides of the new gasket.These engines use a composition gasket. Install it dry (without any sealing compound).Install the new gasket with the word Top on the cylinder head side. Place the cylinder head on the engine.Coat the threads of the stud bolt (no. 8 in the tightening sequence) with Teflon pipe sealant. Install the bolts and tighten them. Tighten them. Install the remaining components in the reverse order of removal.Change the oil and filter.Refill the cooling system and run the engine, checking for leaks and proper operation.

Genuine Jeep Cherokee Cylinder Head

Head

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Cylinder Heads found

View related parts
Jeep Cherokee Head&Valve-Cylinder
Part Number: 68214829AA
$2010.65 MSRP: $2450.00
You Save: $439.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Cylinder With Valves
- Replaced by: 68641999AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2015 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 6 Cyl 3.2L
View related parts
Jeep Cherokee Head&Valve-Cylinder
Part Number: 68214828AB
$2005.15 MSRP: $2435.00
You Save: $429.85 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Cylinder With Valves; Cylinder Head
- Replaced by: 68641998AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2021 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Lux AWD, Latitude Lux FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 6 Cyl 3.2L
View related parts
Jeep Cherokee Engine Cylinder Head
Part Number: 5048020AB
$1075.65 MSRP: $1300.00
You Save: $224.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Assembly Engine Cylinder
- Replaced by: 68641995AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2016 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Head&Valve-Cylinder
Part Number: 68214828AA
$2005.15 MSRP: $2435.00
You Save: $429.85 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Cylinder With Valves
- Replaced by: 68641998AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2015 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 6 Cyl 3.2L
View related parts
Jeep Cherokee Engine Cylinder Head
Part Number: 5048020AA
$1075.65 MSRP: $1300.00
You Save: $224.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Assembly Engine Cylinder Refer To Illustration 105 For Important Engine Identification Information
- Replaced by: 68641995AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Cylinder Head
Part Number: 68575940AA
$1239.75 MSRP: $1540.00
You Save: $300.25 (20%)
FREE Shipping
ADD TO CART
Product Specifications
- Other Name: HEAD-CYLINDER; Cylinder Head
- Replaces: 68517203AA, 68546724AA, 68438243AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022-2023 Jeep Cherokee | 4 Cyl 2.0 L GAS
View related parts
Jeep Cherokee Engine Cylinder Head
Part Number: 5048506AA
$1075.65 MSRP: $1300.00
You Save: $224.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head-Engine Cylinder
- Replaced by: 68641995AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2019 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Head&Valve-Cylinder
Part Number: 68214829AB
$2010.65 MSRP: $2450.00
You Save: $439.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Cylinder With Valves; Cylinder Head
- Replaced by: 68641999AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2021 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Lux AWD, Latitude Lux FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 6 Cyl 3.2L
View related parts
Jeep Cherokee Engine Cylinder Head
Part Number: 68641995AA
$1075.65 MSRP: $1300.00
You Save: $224.35 (18%)
ADD TO CART
Product Specifications
- Other Name: HEAD-ENGINE CYLINDER; Cylinder Head
- Replaces: 5048585AA, 5048020AE, 5048020AB, 5048506AB, 5048020AD, 5048506AA, 5048020AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022-2023 Jeep Cherokee | 4 Cyl 2.4 L GAS
View related parts
Jeep Cherokee Engine Cylinder Head
Part Number: 5048506AB
$1075.65 MSRP: $1300.00
You Save: $224.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head-Engine Cylinder; Cylinder Head
- Replaced by: 68641995AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2021 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Engine Cylinder Head
Part Number: 5048020AD
$1075.65 MSRP: $1300.00
You Save: $224.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Assembly Engine Cylinder
- Replaced by: 68641995AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Overland FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee Cylinder Head
Part Number: 68438243AA
$1297.00 MSRP: $1540.00
You Save: $243.00 (16%)
ADD TO CART
Product Specifications
- Other Name: Head-Cylinder
- Replaced by: 68575940AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2021 Jeep Cherokee | Latitude AWD, Latitude FWD, Latitude Lux AWD, Latitude Lux FWD, Latitude Plus AWD, Latitude Plus FWD, Limited AWD, Limited FWD, Overland AWD, Overland FWD, Trailhawk AWD | 4 Cyl 2.0L
View related parts
Jeep Cherokee Cylinder Head
Part Number: 68228169AA
$1339.65 MSRP: $1620.00
You Save: $280.35 (18%)
ADD TO CART
Product Specifications
- Other Name: Head Cylinder With Valves
- Replaced by: 68429266AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD
View related parts
Jeep Cherokee HEAD&VALV-CYLINDER
Part Number: 68641999AA
$1974.15 MSRP: $2450.00
You Save: $475.85 (20%)
FREE Shipping
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Replaces: 68214829AB, 68214829AA, RL214829AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Cherokee | 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Engine Cylinder Head
Part Number: 5047491AF
$696.97 MSRP: $1025.00
You Save: $328.03 (32%)
ADD TO CART
Product Specifications
- Other Name: Head Assembly Engine Cylinder Refer To Illustration 105 For Important Engine Identification Information; Cylinder Head
- Replaces: 5047491AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014 Jeep Cherokee | Latitude AWD, Latitude FWD, Limited AWD, Limited FWD, Sport AWD, Sport FWD, Trailhawk AWD | 4 Cyl 2.4L
View related parts
Jeep Cherokee HEAD&VALV-CYLINDER
Part Number: 68641998AA
$1968.75 MSRP: $2435.00
You Save: $466.25 (20%)
FREE Shipping
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Replaces: 68214828AB, RL214828AA, 68214828AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022 Jeep Cherokee | 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Cylinder Head
Part Number: 68240843AA
$877.77 MSRP: $1035.00
You Save: $157.23 (16%)
ADD TO CART
Product Specifications
- Other Name: Head Cylinder
- Replaced by: 68276415AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015 Jeep Cherokee | Latitude AWD, Limited AWD
View related parts
Jeep Cherokee Cylinder Head
Part Number: 53010334
Product Specifications
- Other Name: Head Cylinder
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2001 Jeep Cherokee | Classic 4 Door 2WD, Classic 4 Door 4WD, Limited 4 Door 2WD, Limited 4 Door 4WD, SE 2 Door 2WD, SE 2 Door 4WD, SE 4 Door 2WD, SE 4 Door 4WD, SE RHD 4 Door 2WD, SE RHD 4 Door 4WD, Sport 2 Door 2WD, Sport 2 Door 4WD, Sport 4 Door 2WD, Sport 4 Door 4WD | 6 Cyl 4.0L
View related parts
Jeep Cherokee Cylinder Head
Part Number: R5640469
Product Specifications
- Other Name: Head, Engine Cylinder; Cylinder Head
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1997 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 2 Door Sport Utility RHD 2WD, 2 Door Sport Utility RHD 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4 Door Sport Utility RHD 2WD, 4 Door Sport Utility RHD 4WD | 6 Cyl 4.0L
View related parts
Jeep Cherokee Cylinder-Cylinder
Part Number: R5640415
Product Specifications
- Other Name: Head, Engine Cylinder; Cylinder Head
- Replaces: 33007118
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1996 Jeep Cherokee | 2 Door Sport Utility 2WD, 2 Door Sport Utility 4WD, 2 Door Sport Utility RHD 2WD, 2 Door Sport Utility RHD 4WD, 4 Door Sport Utility 2WD, 4 Door Sport Utility 4WD, 4 Door Sport Utility RHD 2WD, 4 Door Sport Utility RHD 4WD | 6 Cyl 4.0L

| Page 1 of 2 |Next >

1-20 of 24 Results

Jeep Cherokee Cylinder Head

The Cylinder Head of the Jeep Cherokee directs the flow of incoming air-fuel mixture while sealing off the combustion process to allow the exhaust to escape. As such, this essential Jeep part affects the power and efficiency of your engine. The Cylinder Head is located on top of the cylinders, forms the roof of the combustion chamber, holds the spark plugs and valves, and directs coolant to regulate temperature. To protect this seal, Jeep employs a sturdy gasket, which is secured using Torque to Yield bolts that are designed to stretch once. This spreads the clamping force evenly and prevents misfires, overheating, and leaks between oil and coolant. A damaged Cylinder Head, whether warped, cracked, or hosting worn guides and burnt valves, can cause a Cherokee to run roughly or lose compression. There are two main styles: the heavy cast iron Cylinder Head found on earlier Cherokee engines and a lighter aluminum Cylinder Head adopted later by Jeep in newer Cherokee editions. The latter sheds heat faster, cuts down on weight for better balance, and tolerates higher compression. Both remain reinforced, though, so port shaping can improve airflow without breaking through the water passages. This has helped sustain Jeep's image as a trusted brand across generations.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Cherokee Cylinder Head at great affordable prices. Moreover, all genuine Jeep Cherokee Cylinder Head come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Cherokee Cylinder Head Parts Questions & Experts Answers

Cylinder Head
33007115
Q: How to remove and reinstall a cylinder head in four cylinder engine on Jeep Cherokee?
A:
Remove the Rocker Arms and Pushrods. Remove the intake and Exhaust Manifolds.Remove the drivebelt(s). Unbolt the power steering pump (if equipped) and set it aside without disconnecting the hoses.On air conditioned models, remove the bolt that secures the air conditioning compressor/alternator bracket to the cylinder head, then unbolt the compressor/alternator bracket from the engine. Set the compressor aside without disconnecting the hoses.Label, then disconnect the wire from the coolant temperature sending unit on the cylinder head. Label the spark plug wires and remove the spark plugs.Remove the ten bolts that secure the cylinder head and lift it off the engine. If the head is stuck to the engine block, it may be necessary to tap it with a soft-face hammer or a block of wood and a hammer to break the seal. Stuff clean shop towels into the cylinders. Thoroughly clean the gasket surfaces removing all traces of gasket material. Run an appropriate sized tap into the bolt holes in the cylinder head and run a die over the bolt threads. Ensure all bolt holes are clean and dry.Inspect the cylinder head for cracks and check it for warpage. 1984 through 1987 four-cylinder engines use different head gaskets than 1988 and later models. The two types of gaskets are NOT interchangeable and require different tightening torques.These engines use stamped steel gaskets. Apply an even coat of a copper coat type gasket sealant to both sides of the new gasket.These engines use a composition gasket. Install it dry (without any sealing compound).Install the new gasket with the word Top on the cylinder head side. Place the cylinder head on the engine.Coat the threads of the stud bolt (no. 8 in the tightening sequence) with Teflon pipe sealant. Install the bolts and tighten them. Tighten them. Install the remaining components in the reverse order of removal.Change the oil and filter.Refill the cooling system and run the engine, checking for leaks and proper operation.