What Steps Are Involved in Replacing an Ignition Lock Cylinder on Jeep Wrangler?

For all the models ranging from 1987 to 1995 begin by removing the cable from the negative terminal of the battery. Subsequently, one has to disconnect the turn signal/hazard warning switches and further the ignition key lamp assembly. Move the lock cylinder to the 'On' position. For 1990 and earlier models locating of a retaining screw will make the cylinder to be withdrawn from the steering column. As for the 1991 and later models, one has to use a thin screwdriver and push on the spring latch to take out the cylinder. Place the lock cylinder into position and then install the screw for the pre-1990 vehicles and be sure to tighten it. The process by which locks are installed is the exact opposite of how they are removed. For models from 1997 through 2000, remove the battery negative terminal a and if the vehicle has automatic transmission put the shift lever in the park position. Insert a small screwdriver or pin punch in the access hole in the lower steering column cover and push the relaease tang on the key lock cylinder to the right while withdrawing the same/rightarrow The replacement of the key lock cylinder is as follows, making sure it correctly locks in, with a snap. If the below 2000 vehicle model key does not turn easily then there arises a problem that does not affect the switch or the lock cylinder, but can include; the shifter interlock cable or a bad button at the back of the key cylinder for the 2001 models and later. Remove the negative cable, put the key into the ignition, and put the shifter in 'park' if the car's transmission is automatic. Repeat and remove the steering column covers, turn the key to ON position, and if logistics has been done then remove the halo ring and keyless entry module. Put slightly forceful punch on the hole available at the base of the switch and at the same time remove the key, this gives access to the cylinder to be pulled out. If the old cylinder has to be replaced, the key is inserted and turned to the On position and the cylinder is placed as straight as possible within the housing and than fitted in to place. Lastly, adjust the key to the Lock position and then follow the steps mentioned above in reverse manner.

Genuine Jeep Wrangler Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Ignition Lock Cylinders found

View related parts
Jeep Wrangler Cylinder-Ignition Lock
Part Number: 5139207AA
$118.11 MSRP: $209.00
You Save: $90.89 (44%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Ignition Lock
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2006 Jeep Wrangler | Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Cylinder Lock-Ignition Lock
Part Number: 5083915AB
$143.26 MSRP: $214.00
You Save: $70.74 (34%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Ignition Lock
- Replaces: 5003843AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Jeep Wrangler | Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Cylinder Lock-Ignition Lock
Part Number: 5003843AB
$143.26 MSRP: $214.00
You Save: $70.74 (34%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Ignition Lock
- Replaced by: 5083915AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Jeep Wrangler | Rubicon, Sahara, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Cylinder-Ignition Lock
Part Number: 5179511AA
$66.15 MSRP: $98.05
You Save: $31.90 (33%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Ignition Lock
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2018 Jeep Wrangler | 70th Anniversary, Rubicon, Rubicon 4WD, Sahara, Sahara 4WD, Sport, Sport 4WD, Unlimited Rubicon, Unlimited Rubicon 4WD, Unlimited Sahara 2WD, Unlimited Sahara 4WD, Unlimited Sport 2WD, Unlimited Sport 4WD, Unlimited X 2WD, Unlimited X 4WD, Unlimited X RHD 4WD, X, X RHD | 6 Cyl 3.6L, 6 Cyl 3.8L
View related parts
Jeep Wrangler CYLINDER/LOCK-Ignition Module
Part Number: 4746667
$66.84 MSRP: $75.65
You Save: $8.81 (12%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Lock Package Ignition Black Plastic; Ignition Lock Cylinder, Lock Cylinder
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Jeep Wrangler | SE | 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Ign Cylinder-Cylinder - UNCODED Black
Part Number: 4746285
$116.18 MSRP: $174.00
You Save: $57.82 (34%)
ADD TO CART
Product Specifications
- Other Name: Cylinder, Ignition Lock; Cylinder & Keys, Ignition Lock Cylinder
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1995 Jeep Wrangler | Sport Utility 4WD | 4 Cyl 2.5L, 6 Cyl 4.0L
View related parts
Jeep Wrangler Lock Cylinder-Set Ignition
Part Number: 55026014
Product Specifications
- Other Name: Cylinder, Ignition Lock
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1990 Jeep Wrangler | 4 Cyl 2.5L, 6 Cyl 4.2L
View related parts
Jeep Wrangler Cylinder
Part Number: J8120081
Product Specifications
- Other Name: Cylinder, Ignition Switch Lock, Uncoded, 1981-84
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1986 Jeep Wrangler | 4 Cyl 1.9L Diesel, 4 Cyl 2.5L, 4 Cyl 2.5L Diesel, 6 Cyl 4.2L

Jeep Wrangler Ignition Lock Cylinder

Similarly, the main purpose of the Ignition Lock Cylinder in Jeep Wrangler vehicles is to enable the starter motor, which, when supplied with an appropriate key that is turned at the correct angle, will start the application's engine. This component is contained in the ignition switch system that provides the required circuits with battery power whenever the appropriate key is turned. Jeep Wrangler models manufactured in the past have employed standard and normal column-mounted ignition lock cylinder for purposes of increasing security and safety on the roads. In the past decades there have been improvements which have necessitated use of coded ignition keys that has a chip embedded with a computer that can only start the car engine when the correct key is inserted. However, it is still possible for the Ignition Lock Cylinder to suffer wear and malfunction and hence creates problems in starting the car. With present generations of Jeep Wrangler models, adoption of advanced keyless ignition systems makes a lot of sense due to less move parts compared to the ignition lock cylinders.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Wrangler Ignition Lock Cylinder at great affordable prices. Moreover, all genuine Jeep Wrangler Ignition Lock Cylinder come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Wrangler Ignition Lock Cylinder Parts Questions & Experts Answers

CYLINDER/LOCK-Ignition Module
4746667
Q: What Steps Are Involved in Replacing an Ignition Lock Cylinder on Jeep Wrangler?
A:
For all the models ranging from 1987 to 1995 begin by removing the cable from the negative terminal of the battery. Subsequently, one has to disconnect the turn signal/hazard warning switches and further the ignition key lamp assembly. Move the lock cylinder to the 'On' position. For 1990 and earlier models locating of a retaining screw will make the cylinder to be withdrawn from the steering column. As for the 1991 and later models, one has to use a thin screwdriver and push on the spring latch to take out the cylinder. Place the lock cylinder into position and then install the screw for the pre-1990 vehicles and be sure to tighten it. The process by which locks are installed is the exact opposite of how they are removed. For models from 1997 through 2000, remove the battery negative terminal a and if the vehicle has automatic transmission put the shift lever in the park position. Insert a small screwdriver or pin punch in the access hole in the lower steering column cover and push the relaease tang on the key lock cylinder to the right while withdrawing the same/rightarrow The replacement of the key lock cylinder is as follows, making sure it correctly locks in, with a snap. If the below 2000 vehicle model key does not turn easily then there arises a problem that does not affect the switch or the lock cylinder, but can include; the shifter interlock cable or a bad button at the back of the key cylinder for the 2001 models and later. Remove the negative cable, put the key into the ignition, and put the shifter in 'park' if the car's transmission is automatic. Repeat and remove the steering column covers, turn the key to ON position, and if logistics has been done then remove the halo ring and keyless entry module. Put slightly forceful punch on the hole available at the base of the switch and at the same time remove the key, this gives access to the cylinder to be pulled out. If the old cylinder has to be replaced, the key is inserted and turned to the On position and the cylinder is placed as straight as possible within the housing and than fitted in to place. Lastly, adjust the key to the Lock position and then follow the steps mentioned above in reverse manner.